Jump to content
SAU Community

Recommended Posts

My front rotors are pretty scored and rooted in my new car (good ol' japanese).. Don't think it would pass a roadworthy and compliance which I am still doing. Its a 1989 R32 GTS-T

So I may as well get some good DBA slotted ones for the track and other fun.

Now it looks as if I have the pov-pack 2pot brakes (no "nissan" printed on them) as I don't think mine is the "m spec". Will this mean I can use the same rotors as any other R32?

From the DBA part database, it lists DBA4909 for R32 fronts - also listed is DBA4963 for R33 which is thicker and larger diameter...

I read a few posts which tend to indicate that the rotor sizes are interchangeable, its just the calipers that can be changed. So why are there two part numbers in the catalogue for R32 + R33 ??

Eventually I will have to upgrade to the R32 4pot or R33 calipers, so I am wondering should I go for the R32 rotors now, or would I be best off going for the R33 rotors for the larger diameter / thickness for better heat distribution??

Link to comment
https://www.sau.com.au/forums/topic/57079-rotors-for-r32/
Share on other sites

Yeah, i want the slotted which is the "4000" part of it.. $180 a piece I have found a place that can do them for.

4909 it is.. Just was wondering as because i have the 2 pot brakes whether there would be any difference in the actual rotors. The listing says 1989-1993 so I assume that includes the 2pot brakes as well.

Thanks guys..

Link to comment
https://www.sau.com.au/forums/topic/57079-rotors-for-r32/#findComment-1103725
Share on other sites

Yeah, i want the slotted which is the "4000" part of it..
No, nothing to do with it. If you look at the cattledog again, you'll see that the model is 909, available in "slotted", "x-drilled" and "4000".

I got some about 3 years ago, plain 909s, slotted.

Link to comment
https://www.sau.com.au/forums/topic/57079-rotors-for-r32/#findComment-1105147
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...