Jump to content
SAU Community

Recommended Posts

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

i also wouldve thought thered be more in it at that boost, bearing in mind i was initially a bit disappointed with 220rwkw from my old 2530, until i realised it sat next to or beat cars with 250+rwkw! while we all like to compare power figures side by side, at the end of the day it is just a figure and its how the car drives that counts.

Mark at MRC think something is holding me back some restristion. I dont expect much more from the turbo. There is heaps of mid range and top end in this turbo.

Injectots i have are apexi 555cc and bosch 044 pump with surge tank and standard pump running in boot.

It was a really hot day during tuning etc, not sure if the dyno figures takes that into equation but it was 45 degrees in the dyno room and didnt have a fan blowing onto the intercooler.

Will hopefully be out the creek on wednesday to run so if people are keen lest get a bit of a crew there. would not mind matching it up with a few others cars.

saw boro's car last night......seems to pull really well

lets wait and see what it does at wsid

PS. Dont wear the same heavy shoes mate :P

Yogi will trying to get off work for wsid. Yeah have been trying to take it easy, its pretty hard tho. should come to the creek.

power sounds right to me, its a gtrs not a t67 or something what do people expect

people expect more than 250rwkw over 1bar, since thizzle set the standard with his 250rwkw at 1bar! :(

but without cams i wouldnt expect much more than 250 even over 1bar. I wouldnt think thered be much more efficient flow left, if that even means anything..

Just took it out for a run now, first cold night since i got it. on 1.3 bar boost at high rpm engine cut-out light comes on, was told that this is pinging although i cant hear anything. going to run it back on dyno to set timing back a few degrees.

I am sure thizzle made 250kw @ 1.3 bar, it is impossible to make it at 1 bar.

i would be very surprised if it made 250 at one bar, but then again who knows due to the difference in dynos.

anyway croat, if the engine light flashes it does mean that the power fc has picked up noise that comes up on the ping reading as (usually) 60 or more. if you have the hand controller you can check it next time, although it might have been a noise other than pinging.

well 250rwkw at 1bar was what he posted after having it tuned at BD4s, only going on what he said. I used to run up to 1.3bar with my 2530, but then when tuning the 2835 my tuner said he didnt want to go over 1.1bar till i did the headgasket. Maybe i could run higher boost with the small turbo coz it would always drop right off at the top end, not sure.

nah i never tuned on 1.3 boro...plus i had slippin clutch. and rushed tune cuz i wanted my car back i think i gave bd4s like 3 hrs on a friday arvo...your 1.3 is alot diffrent to mine man :) somethins holdin it back...cuz i pay out the ass for jap tuners and mechanics maybe ??on 1.3 i woulda got 260-265...your engine wasnt pingin man its runnin very smooth.. it could be tuned a little more i think...

post up the dyno show folks the torque lets see if they still would be dissapinted...

time to take it to yoshi :kick:

btw did ya block that bit yosh said to block up?? cuz ur using that catch can with the air filter on top??? wich results in you loosing boost..

this is about the same power alot of people are making with the GT-RS on sr20det's, although with cams... they dont seem to flow much more then 250rwkw, if thats the power output your after, then the turbo is perfect for responce/power

if you go for some radical duration on your cams you may see more power... the turbines on these turbos are relatively small which does choke them up top when pushed

I got a GTRS installed last week and tuned on saturday and got 255rwkw at 1.2 bar still have standard air flow meter so should be a bit more in it when I get it retuned with a Z32 or something similar. Other mods are full 3 inch exshaust, FMIC, PFC, nismo 555cc injector, exhaust cam, lightened flywheel and ceramic clutch, spitfire coils and bosch 044 fuel pump. Also great response and enough power to keep me satisfied and scare the sh!t out of my mates, also makes the car sound awesome as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
    • That still isn't a lot to go on. I don't have a Y50 Fuga Head Unit wiring diagram. I can say that a lot of nissans of that age shared head unit plugs, so if you are in Australia something like this would probably help: https://aerpro.com/app091# You plug that into the car loom, then either plug the head unit ISO into that (if it has ISO), or you buy and ISO adapter harness that you wire in. Bit of stuffing around, but once you have ISO its easy to change things in future.
    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
×
×
  • Create New...