Jump to content
SAU Community

Recommended Posts

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

A bit of info

This is a Australian company that has them for $2800

This price should include all taxes and freight

Better than Nengun which are over $3000 delivered plus taxes.

There has been some group buys on NS for low as $2500 suit sr20.

http://www.pp-oz.com/

Have a look at new parts and scroll about halfway down.

A bit of info

This is a Australian company that has them for $2800

This price should include all taxes and freight

Better than Nengun which are over $3000 delivered plus taxes.

There has been some group buys on NS for low as $2500 suit sr20.

http://www.pp-oz.com/

Have a look at new parts and scroll about halfway down.

Nenguns current price for a GT-RS kit to suit ECR33 is $2858 delivered.

I have never heard of pp-oz before

Nenguns current price for a GT-RS kit to suit ECR33 is $2858 delivered.

I have never heard of pp-oz before

$2858 delivered correct

Add 10% duty and 10% GST $3425

Thats alot more than $2800.

$2858 delivered correct

Add 10% duty and 10% GST $3425

Thats alot more than $2800.

Well done, you can count.

I dont believe for a minute that the price "pp-oz" is quoting includes all applicable duty and taxes. I would bet that they are being imported that same as via nengun, under the radar with the risk that they *may* get hit for duty and taxes.

Nengun has excellent buying power via HKS and Apexi etc, and im sure if someone took charge here and approached him about a group buy and had genuine interest, he would offer a great deal if a number of turbo orders were placed

Nengun has excellent buying power via HKS and Apexi etc, and im sure if someone took charge here and approached him about a group buy and had genuine interest, he would offer a great deal if a number of turbo orders were placed

I nominate you

Nengun never returns my emails

That's why I have just ordered my Power FC from Greenline for $90 less. :(

I nominate you

Nengun never returns my emails

That's why I have just ordered my Power FC from Greenline for $90 less. :(

I am not part of this group buy, more so watching over it.

I am in the process of buying a set of "New-Spec" HKS GT-SS's for my GTR. If I can jump on board with you guy's that would be appreciated.

- Any discount is a good discount.

I just sent a email to Greenline to order my Power Fc and asked them for a group buy price on the GTRS for rb25det.

Will try Nengun aswell.

Will let you know prices.

Had some pricing back from Greenline

Rb25det kit

Minimum 10 buyers (could be hard to get 10 people)

HKS GT-RS Turbine Kit R33 GTSt: 202,000 yen

Shipping: 15,200 yen (EMS)

TOTAL: 217,200 yen $2785au

HKS GT-RS Turbine Kit R33 GTSt: 202,000 yen

Shipping: 13,350 yen (SAL)

TOTAL: 215,350 yen $2760au

HKS GT-RS Turbine Kit R33 GTSt: 202,000 yen

Shipping: 7,100 yen (Sea)

TOTAL: 209,100 yen $2680au

All prices exclude duty and gst

The EMS price is only $100 less than Nengun's standard 1-off price $2845au

Unless Nengun comes in with a much cheaper price, I would just buy one straight from Nengun and not wait to try and get 10 buyers.

why not ask garret (gcg) to see if they do a garret spec of the gt-rs (or equiv wheel/housing combo), you should get same specs or similar and get the garret price. i mean you can get a gt30 for 2k you should be able to get a gt28rs t3 flange for 2300 tops ? just a thought im sure gcg would be keen, no need for hks label

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
×
×
  • Create New...