Jump to content
SAU Community

Recommended Posts

Chris Rogers : They are 6x4's but unlike some Nissans (like an N14 Pulsar where the 6x4" speaker is on a 6" plate that can be simply removed and replaced with 6" speaker) the factory speaker is on a plastic spacer.

You can buy an aftermarket 6x4" speaker but I'd highly reccomend getting 6" to fit. Even better, go for 6" components.

Remove the factory spacer and with a bit of paper/cardboard mark out the area around where the spacer used to be overlapping onto the metal enough to be able to screw it onto the door. Also you need to mark out where you 6" hole will be so it wont touch any metal.

Use MDF about 12mm thick. Also, before you screw it onto the door, spray paint it so moisture doesnt get to it and make it expand.

I dont know every nissan that has the factory spacer cos I havent worked on every model.

But I know the S13 Silvia and most probably the A31 Cefiro will have the factory speaker on a spacer

You also want circle speakers (i.e. 6") for clearest sound because sound travels as waves, expanding in a circular motion from it's source.

Yeah, I've had a bit of a look under mine, plastic spacers and some truly shagged 6x4's...

My question is, ok you make up the mdf mounting panel, and mount your 6 or 6.5" in. Will you have any issues fitting the door card back over it ? Because the reason I thought the speakers were that smaller size was to fit correctly in that space after the door pocket.

Assuming you get "normal" round 6" in.. wouldn't you also be blocking half of the sound because of the shape of the rectangular grill?

My R32 luckily came with some very recent Addzest 6x4 speakers in the front doors... Quite happy with that because it's one less thing I have to bother doing.

But regarding aftermarket 6x4 speakers, I've seem a couple of brands in the states with them, but nothing here. Ebay had some VERY NASTY looking ones so I wouldn't touch them with a barge pole. Best bet is to do what was mentioned above and make your own 6" speaker mounts.

  • 1 month later...
Has anyone put 6"'s in the front of a R32 yet? If so did you have any problems with them fitting behind the door cover?

Yes. No.

I've fit 6"'s just recently. When you make the backing panel you'll need to bevel the top edge to around 45 degrees to make sure it clears properly. If you use 12mm MDF you shouldn't have any trouble with speaker depth.

If you can wait until this time next week I'm going to post a how to with pics once I get them off my friends digicam.

Mark

edit: Thanks go out to Gareth/BADHABIT for enough info to get me started. :)

and just for reference's sake, i just dummied up my dynaudio splits into the doors of my 32 and they'll fit without too many hastles. you'll need to make a custom mount (i'll be doing mine out of mdf + fibreglass) but they'll fit. there aren't all that many sets of 6-7" mids that hang deeper than my dyns so you shouldn't have too many dramas with most split systems on the market.

just gotta get stuck into Sound Deadener now!!!

d

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...