Jump to content
SAU Community

Recommended Posts

  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

Dry is best obviously. But in the wet they're not the worst tyres, the cheaper falken ZE326 is by far the worst in the wet.

Launch is pretty good..... drift is for fags, so I wouldn't know :D

Oh, and I get them from a RICE Supporting tyre shop in mandurah so those prices might slightly lower than normal prices. Either way, good value for money :)

I got sumitomo HTRZ on the back of mine and have found them to be great

I paid 250buck each for 255/40/17

even when they do let go, they still keep bitting for traction

Or Toyo Proxy are apparently quiet sticky, but the softer they are they quicker they wear down, and at $470 each go, I'll stick with the sumitomo's

i chew thru any tyres i have :)

On my zed i had the potenzas .... nice tyres .... but due to unfortunate circumstances .... such as swerving to miss dogs ..... nails and other gizmos getting stuck in them ..... i went thru them pretty quickly.

On my skyline i have Kumho Supras .... which were nice while they lasted ..... 8 months on and i chewed thru the rubber, the canvas, the belts and another set of canvas ..... yup definately got my wear outta those.

Now i have paulies tyres :D tyres are like kids ..... so much nicer when they are someone elses :)

Dry is best obviously. But in the wet they're not the worst tyres, the cheaper falken ZE326 is by far the worst in the wet.

Launch is pretty good..... drift is for fags, so I wouldn't know :D

Oh, and I get them from a RICE Supporting tyre shop in mandurah so those prices might slightly lower than normal prices. Either way, good value for money :)

can get them from tempetyres over east.. dunno what they charge for the rears, but i know the fronts you get for $140, you can get for $125 + $10 postage per tyre from over there.. so id say ~$200 for the rears too

Nizmo - yeah the kuhmo supra's are nice.. but the 711's are shite.. pity ive got supra's on the front and 711's on the rear :)

On your stocker rims ? Your a dickhead.

I pay $200 for 255/40/17, and $140 for 235/45/17. Cheap Nankang NS-II's that grip like all hell :D Im happy with them :)

today i am picking up my 265/35/18 Hankook ventus (rear) and 235/40/18 front (forget what they are) ill tell ya how the hankook's go sherriff Wan when i get em on

read the whole thread next time b4 calling me a dickhead - Paul (@dad's)

Cool guys thanks.

I was gonna go for the TOYO's as i got an awesome price $800 for all 4 235/45/R17

Anyonw in mel let me know if you need a set. And before you ask NO they haven't fallen off a truck :rofl:

I paid $700 for Firestone Firehawks that size they have been pretty good so far had them on for about 7k kilometers better than the Kuhmos i had on b4

Cheers for all you replies! Keep them coming. I can't believe some of you like the Kuhmo Ecsta Supra's. I have them on now and I hate them! Each to their own.

same, they have probably been the crappest tyres I have had on the 32.

Shaun

i got a new pair of khumo's on the back... cheapies.... 145 apeice, used to have nankangs, but the just meltd in 15000kms, though that was the rears the fronts are stll goin hard....

speak to paul at tyrepower canningvale... a really good bloke who gives great prices....

ps. i think we may be needing a tyre company as a sponser.....

  • 1 month later...

Digging up a bit of an old thread but i've decided on going with the Toyo's. Seem to be the best mix of good reputation from other users and price. The price difference between TPG's and the new T1-R's was negligible so i'm going for the T1-Rs in 255/40/17's for $340 each from Booragoon Tyre Service in Myaree. When I go down there to get them fitted, i'll try and sound him out if he's interested at all in becoming a club sponsor for all the SAUWA members. He's only a small outfit but it would benefit him no end, particularly given the number of you out there using Toyo's.

Await a full review of the tyres once fitted :cheers:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...