Jump to content
SAU Community

  

65 members have voted

You do not have permission to vote in this poll, or see the poll results. Please sign in or register to vote in this poll.

Recommended Posts

Ok, well Ive put a small deposit down on this car pending a full check over next friday at Hyperdrive so im not 100% locked into getting this car however the price is VERY good its done 88'000kms, its manual and Its advertised as:

GTST - MANUAL Series II M-Spec 1996

Now the front bumper/body kit was very badly damaged when he drove it up/down somebodys drive way "explains why its got a new one unpainted on the front"

But its not a SII front at all is it??

Im attaching some picktures so you guys can ahave a look and let me know what you all think.

Series 1. 1.5 or 2

* its advertised as II and I looked on his rego papers and it was registered as a Series 2.

Link to comment
https://www.sau.com.au/forums/topic/65086-gts-t-r33-series-i-or-ii/
Share on other sites

  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

I dont think it had a passengers side air bag. The dash and everything looks so damn clean.. almost looks new.. Its on a slight tilt towards the driver " the radio etc etc.. isnt that a series 2 design?

Butler: Yeah? The front bumper isnt stock

if it didnt have a passanger airbag its definatlly not series 2. But because it does have one in steering wheel it will be series 1.5 hey. Have a look at some pics for a 95 skyline and a 96 you'll see that the steering wheels are different. Those pics show a 95 (series 1.5) steering wheel.

if it didnt have a passanger airbag its definatlly not series 2. But because it does have one in steering wheel it will be series 1.5 hey. Have a look at some pics for a 95 skyline and a 96 you'll see that the steering wheels are different. Those pics show a 95 (series 1.5) steering wheel.

Ahh man.. Im worried now.. It must have at least one airbag because it says SRS airbag under the bonet, It also is dated as a 1996 build under the bonet.

Cheers pozza, Im going to look into the 1995 and 1996 models a bit more..

Its 100% a 1.5...

Has a series 2 motor with series 1 interia and series 1 front end (ie grill, bumer and most importantlly headlights... The series 2 has different head lights. If its a 96 model it cant be a swries 1.. It can only be 1.5 or series 2....

Must be a 1.5, as why would someone replace series 2 stuff with series 1 parts...

Sounds dodge, I've seen a Series I for sale from the dodgiest guy I've seen and it was badged under the bonnet as a 1997.

He even asked me what's the difference between a I, II model !

I think someone on here has a way of telling the year by the chassis number of something,

No that's not a Series II at all, headlights, bonnet, grille, front bumper, interior are all indicating Series 1.5. The only part which is the same as a Series 2, is the colour coded [skyline] panel at the rear, but all you have to do is paint a Series 1/1.5 clear part and it looks the same as a S2.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
×
×
  • Create New...