Jump to content
SAU Community

Recommended Posts

umm the gtst realistcly would do in the 16s, lets not kid our selfs

i owned a R33 GTS-T with a mad exhaust, runnin 12psi boost and it only ran into the high 15's low 16's...

a 32 is only 2.0l as well, so it would run high 16's

either your 33 was running like shat, or you cant drive.

or maybe your exhaust wasnt MAD enough.

ive seen 33's with FULLY SICK exhausts and 12 MEGA psi running 14's

I have never seen a turbo Skyline run higher than a mid 15, stock or modded.

A stock SR20 Pulsar from the early to mid '90s run 16.2. Hell, even a stock base model BA Falcon 4L auto is supposed to run 16 flat or better

.

the common misconception is a 'stock' car...

has anyone ever seen a DEAD STOCK r32 down at the drags?

...most people often call a car with just a 3" exhaust a 'stock' car

i mean stock exhaust, muffler, cat, air filter, boost, fuel... EVERYTHING

the kind of person who takes their car to the drags is the same kind of person who will modify it

i tend to think that i DEAD STOCK r32 gtst with a normal driver would run a 16...

Waz.

Well heres my 2 cents

I have an R31 Skyline with an RB30E in it and the thing was stock as they come and ran high 16's. I added extractors and exhaust and got low high 15's, low 16's. Now I don’t know where every one is getting there information that R32 Skylines stock would run 16's, but my stock R32 seems to be a hell of a lot faster then my R31 and it has been completely stock till about 2 days ago when I added a pod and all that did was make it sound good no noticeable performance. I think people should check there numbers before posting that R32's run 16's.

Just because you have an engine that’s about to die or a bigger engine then a 2.0L and your car is slow, don’t mean the majority of stock R32's are slower then you :kick:

i mean stock exhaust, muffler, cat, air filter, boost, fuel... EVERYTHING

the kind of person who takes their car to the drags is the same kind of person who will modify it

Gimme $50 and i'll go take mine out there and see how slow mine can run :rofl:.. it's auto which would make it even better. oh but its got a K&N filter so i guess it's too highly modified :)

Go on, we will pass the colleciton hat around:)

My stock R32 ran a 13.4 @ 108mph. Gtr and R33 owners call their internally std engines stock, well so am i:)

If you cant run a 15.5 in any std manual id be scratchign my head. I have been in an R32m which other then a air filter is completely std. Im betting it woudl get into the high 14s pretty easily, where is 46n2 when you need him:)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...