Jump to content
SAU Community

Recommended Posts

My 33 came with a Blitz 3inch cat-back exhaust from japan (with cannon).. When idling I rekon it sounds pretty quite/tame, but still very deep.. As you drive harder it gets noticably louder but..

Overall very well balanced cat-back system... Cost about $800 for cat-back or $1500 for full turbo-back system i hear...

I have a very similar sound clip of a blitz exhaust if u want it...

jagr33 (jack) im pretty sure has a twin 2.5" mufflers on his gtr which i think flow just as much as most other 3" or 3.5" systems but are no where near as loud, perhaps you could pm him and ask what model he has?

'quiet' for one person = 'loud' for another

what's my point? get a custom-made exhaust from a reputable exhaust shop and choose exactly how loud you want it

a $2000 brand-name piece of pipe doesn't automatically flow better than a similarly-shaped custom $600 jobbie... you can test a number of muddlers to find one you like if you don't want a cannon one.

but then again, some people just have to have the brand name...

I am yet to own a car (the count is 11 now I think) that has had a brand name exhaust.

All of mine were custom (at least cat back) and are always louder than others I've heard with jap systems.

that's why I asked the question.

hahaha, The liberty RS Turbo I had a few years back.. man that thing had such a deep and loud sound that it was unbearable at about 3200rpm.. it was a little quieter on either side of that rev range.

minimum 4 car alarms would go off in every car park.

the S14 is not that bad, but still loud.

come to think of it, my skyline before wasn't too loud and it was custom..

hmmm.

my exhaust system is a custom 3inch mandrel bent job from turbo back.. its generaly 'quiet' but dont know wat the **** alarm system it was the other day but i started up in an angle park on a side street and set off a car alarm :rofl: was rather funny but yer i havent been hassled about my exhaust by cops yet.. but yer its a plain straight thru system with just the rear cannon 4inch tip.. isnt to bad all up cost was around 1k for the whole system.. with split dump pipe all stainless.. all tig welded

I've got a custom aussy job.

It is a 3" from the turbo back, 3" highflow large cat, larger center resonator (this is the trick to a nice flowing quiet exhaust) and finally a large rear straight through muffler that only 'just' fits. The rear of the muffler is painted black and leaving the muffler is a single 3" s/steel tip. It doesn't attract any attention.

Nor does it have a 1kg milo tin sticker attached. hahah :D

The exhaust has a nice note, doesn't drone and cannot be heard when cruising next to it with the window up, with the window down you can only hear a slight growl.

D&T Performance in Adelaide (google) did the exhaust. One dissapointment with it is the lack of quality or care that went in to the dump pipe.

D&T Performance in Adelaide (google) did the exhaust. One dissapointment with it is the lack of quality or care that went in to the dump pipe.

What do you mean by this? Did they damage something? I ask cause I got my catback done at D&T Performance, and was seriously thinking in getting them to do the full exhaust sometime.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...