Jump to content
SAU Community

Recommended Posts

Well we are fixing a lot of stuff up on my car and i got a highflow turbo, and on the slightest accelation it flutters and on revving, and when not on boost it flutters. Just wondering how we can stop it fluttering so much. any help would be great

Thanks

Link to comment
https://www.sau.com.au/forums/topic/78780-turbo-flutter/
Share on other sites

do you have a pod? And what about the stock plumback BOV? Is that connected? And finally do you have an aftermarket BOV? if you do have an aftermarket BOV try loosening it, mabye the spring is too tight thats why you get flutter.

yep got a pod, no stock bov has aftermarket one, and no matter where it is adjusted it still flutters loosen it off or fully tight still does.

Link to comment
https://www.sau.com.au/forums/topic/78780-turbo-flutter/#findComment-1437482
Share on other sites

same thign happens to mine dude i had a blitz ss and now have a HKS SSQV no matter how loose i make the spring it still flutters like crazt out of the filter when accelerator is released.....i have th estock bov capped off but still in postition at the sake of loosing boost u rekon its worth runnin the stock and the HKS???

Link to comment
https://www.sau.com.au/forums/topic/78780-turbo-flutter/#findComment-1438567
Share on other sites

Aftermarket BOV's have a higher spring rate than factory bov's. So where the factory bov will open up when releasing light throttle, the aftermarket one does not. Please correct me if i'm wrong. when there is no bov this causes a build-up of pressure in the intake piping, slowing the compressor wheel - and hence the flutter. I think the same principle applies to aftermarket BOV's which don't open under light load, but obviously you don't have as much of a pressure build up as you would jumping off the gas from WOT.

There are a few war-threads where everyone has thrown their 2c in about BOVs which might be worth a read such as this.

:P

Link to comment
https://www.sau.com.au/forums/topic/78780-turbo-flutter/#findComment-1438939
Share on other sites

sorry i ment not when accelerating

Basically i'm saying it's not uncommon for car with aftermarket bovs to make the fluttering sound when backing off from light throttle. This is different when it comes to the HKS SSQ bov's and the like. when driving with a heavier right foot, the fluttering noise is by design and made by the BOV (and not the turbine).

:rofl:

Link to comment
https://www.sau.com.au/forums/topic/78780-turbo-flutter/#findComment-1439933
Share on other sites

i've got the same problem at the moment! however, only when i floored in 4th/5th gear from say 2000rpm and it flutter at about 3000rpm. 1st/2nd/3rd gear is fine as it will rev to 7000rpm! i'm thinking it might be the turbo surging. btw it's a GCG stage 1 high flow. anyone experience this before? any help would be appreciated!! :P

Link to comment
https://www.sau.com.au/forums/topic/78780-turbo-flutter/#findComment-1442162
Share on other sites

i've got the same problem at the moment! however, only when i floored in 4th/5th gear from say 2000rpm and it flutter at about 3000rpm. 1st/2nd/3rd gear is fine as it will rev to 7000rpm! i'm thinking it might be the turbo surging. btw it's a GCG stage 1 high flow. anyone experience this before? any help would be appreciated!!  :(

I HAVE THE SAME PROBLEM CRUISING VERY LIGHT THROTTLE VERY NOTICEABLE ON THE FREEWAY IT JUST KEEPS FLUTTERING. I HAVE A GCG HIGH FLOWED TURBO POD FILTER AND AFTER MARKET BOV. IM GOING TO TRY A STANDARD BOV. LET ME KNOW IF ANYONE DOES FIX THEIRS

Link to comment
https://www.sau.com.au/forums/topic/78780-turbo-flutter/#findComment-1443301
Share on other sites

i've got the same problem at the moment! however, only when i floored in 4th/5th gear from say 2000rpm and it flutter at about 3000rpm. 1st/2nd/3rd gear is fine as it will rev to 7000rpm! i'm thinking it might be the turbo surging. btw it's a GCG stage 1 high flow. anyone experience this before? any help would be appreciated!!  :(

Just put on a s/h hi-flow turbo, i believe it may be a GCG unit as it has the sierra-sierra turbine combination and is also b/b core. Whereas ATP replace the b/b core with a bush unit.

If i plant the foot in any gear the turbo spools nicely and puts down the power. If i cruise easily, at 0.5bar the turbo will flutter while i am still accelerating. Boost flutters back and forth between about 0.4bar and 1.2bar, till i floor it or change gear. The previous owner swears he had no such issue with the turbo. And i know my mechanic played arround with the integral gate, while on the dyno.

I have come up with a few possiblities that still need to be tested.

1/ Integral wastegate is not working 100%

2/ The intake pipe may be partly collasping under light loads (harmonics) thus effecting intake air.

3/ Also want to temporarily remove new Turbosmart bov, just to eliminate it as a fault.

Any other suggestions.

Link to comment
https://www.sau.com.au/forums/topic/78780-turbo-flutter/#findComment-1443314
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Just wanted to pop in an update on my setup. The CD swap has been great, I love the mazworks housing for the overall simplicity. I ended up sealing my trans tunnel with a thin sheet of aluminum reused some of the holes on the trans tunnel, and laid some window sealing EPS foam around the edges. Works great, really quieted things down and sealed up the car.  As for the power comment. Right now I am also running about 650whp. with the way the bell housing is attached to the face of the transmission I have zero doubts it would be fine, mainly because the input shaft and main shaft bearings are seated into the bell housing adapter. This means the load is NOT on the bolts to maintain the power, rather into he casing of the bell housing; Yes the bolts are doing some work there, but with both shafts locked in zero worries.  End of the day, the Mazworks solution is the easiest and safest. no need to take your trans to a shop to get milled perfectly, it fits with minimal clearancing, and you can use all your existing clutch and flywheel.  Driving wise the CD has been great compared to the big box, I'll probably swap my final drive at some point. The serial 9 shifter is gooooood, my only qualm is how tight it is, it takes a fair bit to get use to, 5th and 6th are a bit eh/hard to find at times, but maybe I need re-adjusting, and I think my clutch master is very tired and needs a rebuild. 
    • If you are keen, have a look at my build thread. Car is for sale for the right money or straight swap for a F80 M3 LCI.
    • Welcome mate.  No point in over thinking it, buying any one of those cars you mentioned is not a smart or logical choice with the availability of many "better" (re price to performance) cars available to you.  The heart wants what the heart wants, buy whatever it leads you too.
    • Hey everyone! Im so grateful to be apart of this community and ill do my best to be apart of this. Firstly, i'm not disclosing my real name due to in real life circumstances surrounding my privacy and public image (sorry lol) Secondly, The only thing personal I am willing to share is that I'm from Sydney and a descendant of one of Sydneys largest mortgage firms. I got gifted my first ever car, a 2022 Porsche Cayenne and I love it to death. Ive been driving it for about 5 or 6 months now and honestly Im so grateful for my parents for gifting me this vehicle. However recently I've been working my ass off to afford my second car (which I need help deciding soooooo community help me out please?). Once decided, im planning to try modify it myself. Recent I've been thinking about getting a Skyline, particularly a 25GT or GT-V, yes I know overrated as hell, but I'm also considering a Chaser which I recently came to love. However my dream is to one day own a 180SX (So hard to find clean versions and im not really into importing).  Lastly before I send this off, I want to apologize if I sound tacky or pretentious. I try not to and want to genuinely learn from everyone and anyone. (Im no expert in this area) Thanks for reading!
    • I've got three stashed away but it's starting to get silly with the prices 
×
×
  • Create New...