Jump to content
SAU Community

Recommended Posts

One of the best articles i have seen in here...

Great job... Will consider doing one myself...

Although i dont use the car round the track just down the 1/4 and street so i have not needed one but im tinkering with it now for a qQLD track day as i think circuit racing is gonna be more fun....

When you don't have a thermostat your oil cooler always has oil going through it. When it's cold and you're trying to warm your engine up, or when it's just really cold your oil is always getting cooled.

You don't want this because your oil can actually be too cold.

How much would an oil thermostat setup cost? is it easy to intergrate that into one of these oil coolers that seem to be going round at the moment for the 350 - 400 mark?

V.Interested as i am thinking about donig some track work with my car and i think that this would be a good thing to do to add a little reliability to the motor :rofl:

Cheeeeeeers

Great article - and great in theory, but I have just put a Trust copy aluminium sump on my S15 and it has reduced normal oil running temp from 180 degrees fahrenheit, to under 150 degrees fahrenheit. I have not track raced it yet with the new sump, but am positive it would even help here too.

It was a 5 minute job to install, and you don't run the risk of ever popping a fitting or hose, and lunching your engine. For non-track cars, I think the higher capacity sump is the way to go! It has fins (like a heatsink) for cooling, is internally gated to stop oil surge, and carries 1 litre more of oil. Can't go wrong! That said, oil coolers are great too, just thought I'd point out the benefit of my new acquisition, and how suprisingly well it works at cooling.

Great article - and great in theory, but I have just put a Trust copy aluminium sump on my S15 and it has reduced normal oil running temp from 180 degrees fahrenheit, to under 150 degrees fahrenheit. I have not track raced it yet with the new sump, but am positive it would even help here too.

It was a 5 minute job to install, and you don't run the risk of ever popping a fitting or hose, and lunching your engine. For non-track cars, I think the higher capacity sump is the way to go! It has fins (like a heatsink) for cooling, is internally gated to stop oil surge, and carries 1 litre more of oil. Can't go wrong! That said, oil coolers are great too, just thought I'd point out the benefit of my new acquisition, and how suprisingly well it works at cooling.

For road use and the occasional blast the standard oil cooler attached between the sump and the filter on the RB engines (don't know about the S15) is quite satisfactory. For track use though, you will need an oil cooler as your oil temperature would be exceeding 130 degrees C (260 degrees F) after a couple of laps.

Sounds like an easy job to replace the sump on the S15, I know the VL with the RB motor is a B...... job to change the sump.

Cheers

  • 2 months later...
  • 4 months later...

Sorry to dig up such an old thread but I think it's worthwhile. Has anyone run the lines directly from the cooler to the turbo? Is that a bad idea? My reasoning being I am about to go with a high mount setup, and if I could use the cooler lines as the "link" from engine to turbo it would save me on buying extra hoses.

Sorry to dig up such an old thread but I think it's worthwhile. Has anyone run the lines directly from the cooler to the turbo? Is that a bad idea? My reasoning being I am about to go with a high mount setup, and if I could use the cooler lines as the "link" from engine to turbo it would save me on buying extra hoses.

Hi JimX

I wouldn't suggest using the Olil Cooler setup to feed the turbo with oil!

If you do, remember the oil pickup for the turbo on the engine block has a very small hole in it. This is to meter the correct amount of oil fed to the turbo bearings. You will have to fabricate a fitting.

Cheers

Hi JimX

I wouldn't suggest using the Olil Cooler setup to feed the turbo with oil!

If you do, remember the oil pickup for the turbo on the engine block has a very small hole in it. This is to meter the correct amount of oil fed to the turbo bearings. You will have to fabricate a fitting.

Cheers

Thanks for the info. I had another look over the pics of the cooler setup and realised that even if it was possible, it'd be overly complicated for no real benefit other than saving a bit of hose and space, because I'd have to do something with the factory oil filter outlet, or just run 2 oil filters. Both of which are going to be more of a headache than it's worth. Also it'd be nigh on impossible to quickly remove the cooler for whatever reason and keep the car drivable, since the fittings will be all wrong and hoses may not reach anymore. I just had some crazy idea in my head without checking reality. Sorry about that!

  • 1 month later...
  • 1 month later...

Great tutorial, thanks for putting the time in to write it up and update the thumbnails. It has encouraged me to mount my relocator that has been sitting on the bench for nearly a year...

As an aside, can you use any oil cooler? That may sound weird but I've seen a whole lot of R33 auto trans coolers going for $30ish in the for sale section. Are coolers made to suit specific viscosities?

Cheers

just a quick question, oil volume, do you add extra oil once you have installed the cooler?

i have a kit sitting here ready to go on (need to find the rubber o rings) but am unsure if i need to add extra oil to engine??

brain says yes, just wanting to confirm...

cheers, Matt

Edited by rsx84
  • 2 weeks later...
just a quick question, oil volume, do you add extra oil once you have installed the cooler?

i have a kit sitting here ready to go on (need to find the rubber o rings) but am unsure if i need to add extra oil to engine??

brain says yes, just wanting to confirm...

cheers, Matt

As Syphon says "yes" is the answer.

Additional oil is required to fill the pipes and the oil cooler.

I have estimated an additional 1/2 litre for this purpose.

Cheers

As Syphon says "yes" is the answer.

Additional oil is required to fill the pipes and the oil cooler.

I have estimated an additional 1/2 litre for this purpose.

Cheers

Hello all,

I have a gtr33 and recently purchased a trust oil cooler for it.

I gave it to a reputable place today(near my work in Campbellfield)

After 2 hours of work the mechanic said he cannot fit the thing in the front right panel.

I said "i knew that...the only place i have seen them fitted is the front left panel."

He went on to say the hoses are not long enough for that...

Anyway in my case do i have to run my hoses under the engine?

And please someone give me a place i can go to have this fitted in Melbourne.

I paid $1000 for the unit and unlike your coolers this has a thermo ,and brackets to fix into place.

(Trust thinks of everything except for the dum-wit that installs it) :P

Thanks

  • 3 months later...

When looking from the front of the car they are usually mounted on the right side (drivers side) as its closer to the oil filters standard location. Also alot of these kits do include thermostats, but from what ive heard they arent necessary in australias climate.

Also nengun sell those trust kits for ~$800

Just realised how old this thread was lol, possibly why the price is different :laugh:

Edited by Godzilla32

I am having a couple of "issues" after installing one of these kits.

My oil light stays on for about 1 second every time I start the car. I am presuming it takes this long to prime the cooler lines, core and filter. Doess this happen to anyone else?

Originally I used a Z30 oil filter, which is quite large and the oil light would stay on for about 2 seconds, but I switched to a much smaller Z160 and now it's down to ~1 sec.

Second issue, I did an oil change yesterday, but when I drained the oil only 3.5 litres came out. Obviously the rest is still in the cooler core and lines. How does everyone else go about flushing the rest of the oil out. With around 1.5 litres of dirty oil still in there, I'm not feeling the normal warm and fuzzies I do when I do an oil change due to the fact I have simlp diluted all that dirty oil.

Do these things happen to anyone else, or have I done something wrong? I have definately plumbed everything correctly going by this DIY, so I just wanted a bit of reassurance.

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...