Jump to content
SAU Community

Recommended Posts

Hey Guys

1993 GTR R32 Vspec

R33 N1 engine

HKS GTSS turbos

HKS cams and cam gears

Cusco coilovers

Greddy intercooler and inlet piping

HKS oil cooler

300 ZX air flow meters

Power FC

HKS exhaust

Advan 17 inch wheels

Upgraded castor rods and sway bars

Upgraded clutch

HKS boost controller

Greddy turbo timer

Recaro seats

HKS super sequential BOVs

Brembo brakes

After market dash

upgraded fuel system

500+ HP

Body kit and wing.

Extremely fast.

No pics until complied.

Michael

Link to comment
https://www.sau.com.au/forums/topic/81439-r32-vspec-bombed-33k/
Share on other sites

  • 2 weeks later...

If the car has just been complied, why has the price gone up please?

Hey Guys

I need 20K up front and 7K after compliance. This is dirt cheap as I need cash ASAP. Take advantage.

Car is in the country and ready to be complied. Can do written agreement etc.

Michael 0414561121

1993 vspec GTR

85,000 kms

N1 engine

Advan wheels

Aftermarket exhaust.

Trust intercooler and piping.

Suspension

And much more.

  • 2 weeks later...

Hey Guys

Have been offline for a while so will repond to questions soon.

Car is at compliance now.

Car is a Vspec BNR32-305136.

(Have checked this number in Japan and Aus: car has vspec oil cooler, brembos, etc)

N1 block etc (will provide number soon)

Will have pics after car is tidied up. Many things had to be changed for compliance.

M

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
×
×
  • Create New...