Jump to content
SAU Community

Recommended Posts

Can you use an R33 brake stopper? Or does it need to be specific for a WC34?

Yes but will needed to have mods done ,

I did one for BUBBA ,& have same type on mine but modded different to his,

$300+ added to $300+ doesnt equal $10000 chuckie lol

Why don`t you worry about the details, $300+$300 + pads + lines + brakestopper is $1000 ok if you can get pads lines & stopper for unders $400 you done well .

but i guess you don`t read to well ,Just stick to your own type of car THANK YOU

I thought he was more going that you put too many 0's. Figured you meant 1,000 but you put 10,000 :P

Thanks for info on stopper. Anyone able to confirm this?

Sorry if this has been answered, but haven't had time to read the thread properly. Just chasing part numebrs for front and rear brakes on a s1 rs4.

From the first post, am I right that pads are:

1250BP (F)

1144BP ®

And front rotors are same as S14 (DBA4909)?

Anyone have a part number for the rear rotors?

REALLY ,

IF YOU HAVE NOTHING GOOD TO ADD IN THREAD DON`T POST CRAP ,PEOPLE TRY TO GET INFO NOT DRIBBLE :cheers:

Yes, Really!!! Pretty sure I did add something good - I added some clarity, because you dont seem to be able to post a coherient response yourself.

I wouldnt want someone thinking they needed to spend $10k on brakes, irrespective of if they own a C34 or an M35 :)

should i put 'lolz' at the end of the line instead of 'lol'?

i was joking chuckie!!!!!

anyway, i should add that brake stoppers were one of the best brake mods i did to my cars. cant find one for M35 tho which sucks

I bought mine from a group buy but I can't remember who organised it.

According to the Cusco website they list the R33 same part number as WGNC34 but different from WGC34 (2wd) so R33 one should fit.

http://www.cusco.co.jp/en/pdf/Brake%20master%20cylinder%20stopper_nissan.pdf

Why Waste MONEY doing that on Rear

Because all though the rear 'axle' as a component does less of the overall vehicle braking, it's also got substantially smaller hardware in which to do it with, so the rear brakes, more often than not, work just as hard in the back as they do in the front when pushed hard. The biggest mistake people make is neglecting the rear, hitting the hills/track, having the rear fade out without them noticing, and put more pressure on the front, which fade, and then get blamed...

When it comes to pads in particular, there's VERY few applications where we don't recommend running the same pads front and rear. VERY light front wheel drives and Porsches (the later for fairly unique reasons) are the two major exceptions. And the same thought process have to be applied when discussing upgrades and caliper choices.

Because all though the rear 'axle' as a component does less of the overall vehicle braking, it's also got substantially smaller hardware in which to do it with, so the rear brakes, more often than not, work just as hard in the back as they do in the front when pushed hard. The biggest mistake people make is neglecting the rear, hitting the hills/track, having the rear fade out without them noticing, and put more pressure on the front, which fade, and then get blamed...

When it comes to pads in particular, there's VERY few applications where we don't recommend running the same pads front and rear. VERY light front wheel drives and Porsches (the later for fairly unique reasons) are the two major exceptions. And the same thought process have to be applied when discussing upgrades and caliper choices.

+1 on all of the above.

Might also add though that a good street setup for me is to try to get a little more bite/bias on the rear.....but there are problems with this setup as you can very quickly run out of talent!blush.gif

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...