Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

post-94823-0-13662800-1343084266_thumb.jpgOk just a recap of my brake upgrades. We did a trial fit on my NM35 ARX-four and the R34gtt 4pistons calipers with a M14 bolts is a straight bolt on affairs. No modification. My dust shield is non existent so no issues there. Also the brake hose is a straight bolt-on.

The Stagea came with a longer bolt compare to the R34gtt and will be using the longer bolt come upgrade time. Next is to get a pair of rotors from R34gtt.

Unfortunately the factory alloys would not clear the calipers so I will be using a 15mm hub centric spacers. New alloys could fix this problem but not an option atmo.

Edited by M35

post-94823-0-13662800-1343084266_thumb.jpgOk just a recap of my brake upgrades. We did a trial fit on my NM35 ARX-four and the R34gtt 4pistons calipers with a M14 bolts is a straight bolt on affairs. No modification. My dust shield is non existent so no issues there. Also the brake hose is a straight bolt-on.

The Stagea came with a longer bolt compare to the R34gtt and will be using the longer bolt come upgrade time. Next is to get a pair of rotors from R34gtt.

Unfortunately the factory alloys would not clear the calipers so I will be using a 15mm hub centric spacers. New alloys could fix this problem but not an option atmo.

I also used the longer Stagea bolts when I fitted mine; I think the mounting points on the R34 must be a fair bit thinner.

They do protrude through the caliper mounting tag, but are still 4 mm away from the rotor.

Are you not using the rotors you have in the pic? They look to have a decent amount to meat left. You could always have them skimmed and slotted; would be cheaper than new rotors.

A 15mm spacer on the AR-X rims will actually put them at a nice position in the arches.

I also used the longer Stagea bolts when I fitted mine; I think the mounting points on the R34 must be a fair bit thinner.

They do protrude through the caliper mounting tag, but are still 4 mm away from the rotor.

Are you not using the rotors you have in the pic? They look to have a decent amount to meat left. You could always have them skimmed and slotted; would be cheaper than new rotors.

A 15mm spacer on the AR-X rims will actually put them at a nice position in the arches.

No not using the factory rotors, diameter is slightly out. 296x24mm for stagea. The pads sits slightly taller than the disc and there is a 6mm gap(3mm) either sides of disc to pads. So will have to use r34gtt rotors. Im hoping to get the conversion done all under $1k.

No not using the factory rotors, diameter is slightly out. 296x24mm for stagea. The pads sits slightly taller than the disc and there is a 6mm gap(3mm) either sides of disc to pads. So will have to use r34gtt rotors. Im hoping to get the conversion done all under $1k.

Ahh, gotcha, they're the AR-X rotors!

I thought it was a GT-t rotor! Carry on, pay no attention to me. :whistling:

You should be able to get a set of RDA slotted for around $300; I realise you're in NZ but as an example.

http://www.ebay.com.au/itm/SLOTTED-Nissan-Skyline-R34-GTT-Front-Disc-Brake-Rotors-NEW-PAIR-WARRANTY-/110916761159?pt=AU_Car_Parts_Accessories&hash=item19d3277647

And a set of Remsa Pads for under $100 from GSL Rallysport (forum sponsors) these things are pretty impressive for the price.

Daleo and M35, do you need the rears too, do you think, or can we just stick with the M35 OEM rear brakes, when combined with the R34 GTt fronts? Do the R34 rears actually bolt up?

And you are using the M35 brake lines for the 4 pots, right?

M35, does your ARX have 17" wheels on it? I'm really keen on this setup myself, if I can get away with just spacers - quite like the later factory wheels, despite being only 17s.

Thanks in advance for any advice.

Daleo and M35, do you need the rears too, do you think, or can we just stick with the M35 OEM rear brakes, when combined with the R34 GTt fronts? Do the R34 rears actually bolt up?

You'll be fine sticking with the OEM rears; the R34 rears don't bolt straight up. Yet.

And you are using the M35 brake lines for the 4 pots, right?

Standard lines go straight in; but I remove the double flare seat from the caliper.

M35, does your ARX have 17" wheels on it? I'm really keen on this setup myself, if I can get away with just spacers - quite like the later factory wheels, despite being only 17s.

Thanks in advance for any advice.

Daleo and M35, do you need the rears too, do you think, or can we just stick with the M35 OEM rear brakes, when combined with the R34 GTt fronts? Do the R34 rears actually bolt up?

And you are using the M35 brake lines for the 4 pots, right?

M35, does your ARX have 17" wheels on it? I'm really keen on this setup myself, if I can get away with just spacers - quite like the later factory wheels, despite being only 17s.

Thanks in advance for any advice.

Sorry I must correct that. My car is a PNM35 ARX-four with an 18' factory alloy rims. Im not worried about the rear brakes yet.

Edited by M35

Sorry I must correct that. My car is a PNM35 ARX-four with an 18' factory alloy rims. Im not worried about the rear brakes yet.

Just check the sliders, my rear brakes were seized, couldn't really tell either.

I only ask coz I replaced the brake pads a while ago, one had morn that much there was no pad left and it was grinding into the backing plate. I was told then to check the shaft for ply but totally forgot until i read these posts... i'll check it out now

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Fark what are the changes of that snapping like that, clean. Nek minnit, custom radiator goes in, with built in oil cooler like those discontinued PWR ones from yesterdeacades ago
    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
×
×
  • Create New...