Jump to content
SAU Community

Recommended Posts

  • Replies 227
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Wayne 'RUS' has trade plates he may let u borrow.

What car would they go on?

Be my car, and like i said im happy to pay for them...do you have a number, perhaps email me.

If i can get tradeplates, just have to ring and see if my car is in one piece ;)

Pete, yeh its available but its a bloody auto :lol:

I think all this organising for people to get up there is a little confusing.  So i've tried to spell it out so everyone knows whats going on

Meeting at my place Sat @ 12pm (FTG):

Scotsman, Min, Bec

Blaise

Snowie and Alan

West + HLT4EVA

Adz and Dee

Matt (Marvic) and Ang

Meeting at Lillydale Sat @ 12:30pm (Last BP on Left out of Lillydale):

James and Bris?

Kim? (starionturbo)

Ant?

Meeting at Healsville, Sat @ 1pm (Coles car park LHS of HWY):

Matt and Jena (WRX)

Meeting at Buxton, Sat @ 2:00pm For Burger Lunch:

Geoff and Nelle

People cruising up on Sun Morning @ 6am Bayswater Maccas:

Ferni

Pete

M-Spec

People I don’t know what they are doing (assume we meet them in Benalia):

Darren

Tom

hi guys, where are u guys meeting up along eastern freeway? which part of eastern freeway?

Can anyone do me a favour by grabbing me a 20lt can of the GT+ off VPW on the otherside of town if you happend to get them as well ? I'll pay when we meet up at Chris's place?

I should be good to meet some of those needs as it's a 5 min drive. Let me know if anyone else needs some.

Geoff

Ohh and a helmet aus complied.

and if your snowman, a radio tuned to triple M so you can listen to the Footy while cornering at 240km/h. ;)

If I get up to 240km/hr at Winton then I've missed a turn somewhere! LOL

:D

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...