Jump to content
SAU Community

Recommended Posts

  • 1 month later...
  • Replies 63
  • Created
  • Last Reply

Top Posters In This Topic

The 5.5-6.8ohm resistors are the ones to use.

10W is fine providing you mount them to a metal box and mount the pack outside of the engine bay (as the origional gtr resistor pack is)

Reason being is when the resistors get hot they don't perform as they should.

So even with the propper GTR resistor pack in a GTST you shouldn't mount it inside the engine bay.

I prefer to use the 15w+ watt resistors encased in a heatsink.

Edited by Cubes

So the MR30 dropping resistor will do the same job as the GTR one?

I measured one I had lying around and it was 6.8 ohms.

Doesn't the R32 gtst power fc have 440cc injectors as an option on the injector menu?

Does that mean they anticipate people using GTR injectors as an upgrade?

I can't read my Jap manual so I can't tell what they consider safe impedence.

I'd sure hate to toast those transistors.

There is no option for selecting injector types.

There is only a trim. Inside the PFC it has stored the stock injector values, you then either do an overall trim or change every cell in the map to achieve the correct afr's.

The issue with an overall trim is you often run out of adjustment via the pfc. From memory 1.4? is the most you can adjust to. If making a lot of power and using a trim this WILL cause problems.

The only propper way to do it is do a complete fuel map tune with no trimming.

OK, so the bit in the manual with injector sizes just shows you how to calculate trims?

eg. 270cc / 440cc =.6136

Will it cope with that until I get a full tune?

So the MR30 dropping restistor (6.8 ohms) will do the the job with the pfc and gtr injectors?

The 5.5-6.8ohm resistors are the ones to use.

10W is fine providing you mount them to a metal box and mount the pack outside of the engine bay (as the origional gtr resistor pack is)

Reason being is when the resistors get hot they don't perform as they should.

So even with the propper GTR resistor pack in a GTST you shouldn't mount it inside the engine bay.

I prefer to use the 15w+ watt resistors encased in a heatsink.

A 6.8oHm in series with the ~2oHm of the injector, at 12V will draw 1.36A.

So at 1.36A the 6.8oHm will dissipate 12.577 Watts.

I've done the calcs and had a read of the resistor specs.

The 10w is ok and the resistors will handle it, I believe there's another bloke on SAU running 10w and a few over at SDU, you wouldn't want them getting hot, though. I wouldn't do it. :D

The injectors see a little more than 12v. More like 13.8v, I use the 25w Aluminium Housed Resistors to be on the safe side.

Edited by Cubes

Also remember that you aren't running at 100% duty either , so the current flow will be at a reduced ratio following along with the duty cycle of the injector. (unless you are right on the edge..)

Better to be safe than sorry though.

I wired in 10watt, 10 ohm resistors in series with each injector, they are all taped up along the fuel rail, they have been working fine for the past 2 weeks, mine dont see much heat because where they sit the fan blows air straight down the fuel rail, im yet to measure their temps though with the infra thermometer.

Why you must run a resistor pack.

http://www.hondata.com/techlowohminjectors.html

Those looking for the R30 resistor pack; its located behind the strut on the passenger side. Very easy to see. Be sure you grab the complete plug (male and female) with some wire to spare.

Edited by Cubes
  • 3 months later...
  • 10 months later...

digging up old threads again :D

I have just installed GTR injectors and used 10watt resistors from farnell. they are 6.8ohm and are wire wound with heatsinks. I picked them because they are rated to 275deg c. the part number is 950-8015

find them here:

CLICKY CLICKY

they cost about $28 for 6 :P

Edited by CEF11E

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...