Jump to content
SAU Community

Recommended Posts

there is no such thing as "GTR offset" offset comes in numbers only.

saying GTR offset is the same as saying "stage 3" mods.... it means you are of the ghey.

basically they are saying that they are of the opinion those rims will only fit on a GTR.

you need to ask what the offset is before we can tell you anything.

Need a reply ASAP guys, been reading for a bit but don't have time to find the info I need. I currently have 18x9" lenso d1rs on the rear of my 34 GTT, unsure of the offset. I'm looking at going 10" but the wheel place said they only have GTR offset. Will these fit under my standard guards ? Car is standard height. I just don't want them to stick out to much.

Any advice is appriciated.

and finding out what your current wheels are would make it really easy with a few measurements.

it should be written somewhere on the back of the rim/spoke of the wheel. Concentrate more on getting the right offset than getting 10" wide wheels

Hey guys newbie with offsets etc but looking at running 19x10 +42 (rears) with 10 or 15mm spacers and rolled guards and 19x8.5 +15 fronts.

Tried my mates starcorp impuls and they were 19x9.5 +40 and they just didn't clear stock suspension on the rears so I reckon with the guards rolled and spacers it should be sweet?

Series 2 GTST stock suspension/ride height

So I've found some offsets I like, i'm just not sure on size.

How will 19x9.5 +13 Front and 19x10 +9 Rear go on a Series 1 R33gts-t?

The 33 I looked at had 18x9.5 +13 Front and 18x10 +9 but the rims looked a little small. Anyone able to tell me if the 19's will rub anywhere?

So I've found some offsets I like, i'm just not sure on size.

How will 19x9.5 +13 Front and 19x10 +9 Rear go on a Series 1 R33gts-t?

The 33 I looked at had 18x9.5 +13 Front and 18x10 +9 but the rims looked a little small. Anyone able to tell me if the 19's will rub anywhere?

Not 100% but id say rolled guards and a spacer will be needed in the rears.

Not 100% but id say rolled guards and a spacer will be needed in the rears.

Yea will need to be rolled for sure, I could even handle a little bit of pumping but only slight. I'm more worried about hitting struts or something like that.

So I've found some offsets I like, i'm just not sure on size.

How will 19x9.5 +13 Front and 19x10 +9 Rear go on a Series 1 R33gts-t?

The 33 I looked at had 18x9.5 +13 Front and 18x10 +9 but the rims looked a little small. Anyone able to tell me if the 19's will rub anywhere?

in the 18" size you will need to pull the guards and remove the front liners if you want it to be low and look good.

i'd suggest looking at 235/40 fr and 245/40 r

the 19's in the same size will look worse, as 19's are too big for the r33 shell.

18's not only look better but are often cheaper and have a much wider variety of tyres to choose from for less money. not to mention that you get a little more sidewall with an 18 which make it easier to tuck and will give a better ride.

i'd imagine a 19 will fit the same as long as you go for a rubber band tyre...

once upon a time there was a thread about 22's on a 33 and I reasearched and drew up an incredibly accurate, scientific graph that represents R33 rim size.

med_gallery_36777_3194_7867.png

now what you will see here is that whilst 19's wont have you listening to feminem or dancing to richard simmonds, they are still considered to be mildly homo when placed on a 33.

An 18/19 Stagger is probably the limit of charles bronson, however this is tough to pull off well.

Hi guys - looking to get koya drift teks 17x9 wheels for my r32 - the guy selling them said they'll probably fit but i might need to get the guards rolled - i'm fine with that, however is there a way of checking whether they'll clear the callipers or not? Type M's have bigger callipers from what I've heard. They came off an r32 but he doesn't know if it was a type m or not.

With the research I've done from this thread, offset doesn't matter with calliper clearance, he wasn't sure of the offset but said he thinks its +20 :/

Thanks in advance :)

Actually, changed my mind and decided to go with another brand 17x7's with wider tyres ... tried looking but still can't find a picture of how this width would look on a 32 gtst with around 25-35 offset... wondering if this would fit the guards nicely with wide tyres (255's)

Edited by agentx


  1. Need a reply ASAP guys, been reading for a bit but don't have time to find the info I need. I currently have 18x9" lenso d1rs on the rear of my 34 GTT, unsure of the offset. I'm looking at going 10" but the wheel place said they only have GTR offset. Will these fit under my standard guards ? Car is standard height. I just don't want them to stick out to much.
    Any advice is appriciated.

Sorry mate, there is no way we can make sense of your situation based on the description you just gave.

If you are unsure of the offset (of either your current rims or the 'GTR offest') then you have no chance of urself or anybody else undersatnd and solving ur issue.

10's can fit without too much trouble but they have to be the right offset...

Otherwise take the time to scroll thru the pages of info here and you will find an exact of similar case of what you are asking which will answer you question...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...