Jump to content
SAU Community

Recommended Posts

Okay so it has come down to the day of actually pretty much buying my rims.

Starting to get cold feet!!

18x9.5 + 22 like what Hectic is running

or be a little safer and go

18x9.5 +30

I CANT CHOOSE!

The +30 will be a little better for not getting police attention.

Would the guards still need a little roll even if I am running camber from my coilovers

I have some XT7s on order, 18x7.5 +35 fronts 18x8.5 +32 rear. Just wondering what size tires you guys recommend for a nice fit for these rims. I'm not a fan of stretched or balloon looks

What do you think of toyo proxie 4s?

I'm kinda a granny driver lol but I occasionally give it a squirt. My r32 is basically stock, just an FMIC an uped boost, at a guess 160ish KW

The kumhos, are they a soft compound? How much are they roughly?

Im getting some racing hart rims for my R32 GTR and want to know if they will fit.

They are 19x10.5 +15

Ive been told they will fit. Ive looked up the jap site for the rims and think they might be 19x10+15 tho.

Anyway will these fit under my car?

What mods will be needed so theres no probs?

Im getting some racing hart rims for my R32 GTR and want to know if they will fit.

They are 19x10.5 +15

Ive been told they will fit. Ive looked up the jap site for the rims and think they might be 19x10+15 tho.

Anyway will these fit under my car?

What mods will be needed so theres no probs?

I would be keen to get that checked. That is a VERY large rim for the 32gtr. 33/34 R's may be able to run them but I am under the impression the 32 guards are smaller then 3/4s. Can anyone back me up on this?

Found out they are 19x10+17

Trial fitting tomorrow then choosing the tyre size. Bloke reckons prob 265 max on there.

Will put up pics when fitted. Fingers crossed. Definately going to fill the guards. lol

Found out they are 19x10+17

Trial fitting tomorrow then choosing the tyre size. Bloke reckons prob 265 max on there.

Will put up pics when fitted. Fingers crossed. Definately going to fill the guards. lol

Yeah, even 265's may be a sqeeze. I got 245 running on 10.5 and it has decent stretch, but not too excessive. 265 is the optimum size (I do believe) for 10's. Do 32 Rs come with 17's from stock?

I ended up swapping my CR Kai's for Buddyclub P1 Qf's. My only concern now is that I've gone from a +22 to a +17 and haven't had a chance to trial fit. Will they fit ok? Will I have an issue if I want to upgrade to bigger brakes in the future?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...