Jump to content
SAU Community

Recommended Posts

Yeh :whistling: Nice car :wub: it

The black looks OK but I love the difference a bit of colour makes, I think the cars look different in a good way. Black looks more threatening and lighten them up adds a little class , well until you see the FR34K , haha

Smart plates and got the R34 in nicely :thumbsup:

First off, I don't know a damn thing about cars. At all.

But, I was wondering if 16 inch rims will fit on an ENR33 gts-4. I just bought these to replace some nasty rims.

205 / 65R15 are the original tires. They are on right now.

205 / 50R16 are the tires I want to put on.

3b347d93fb.jpg88e334f9bd.jpge3887962d9.jpg

First off, I don't know a damn thing about cars. At all.

But, I was wondering if 16 inch rims will fit on an ENR33 gts-4. I just bought these to replace some nasty rims.

205 / 65R15 are the original tires. They are on right now.

205 / 50R16 are the tires I want to put on.

I would say that since you have them on hand, go ahead and test fit them. Just by the look of them, it would seem you will not have any issues,

Hello All,

Skyline model: R32 GTR V-Spec (93)

Wheel Type: Weds Kranze LXZ

Wheel diameter: 19" (front and rear)

Wheel width: 10" (front and rear)

Wheel offset: +19 (front), +15 (rear) dish all around but more in the rear

Tyre size: 275/30/R19

Modifications: nothing....Front - spokes clear the front brembos by 1-2mm, full lock, no scrubbing. Rear - about 20mm clearance from top of rear tyre to underside of rear guard lip. Occasional scrubbing if I hit a pothole. Side wall of tyre comes past the rear guard by 3-5mm.

Hello All,

Skyline model: R32 GTR V-Spec (93)

Wheel Type: Weds Kranze LXZ

Wheel diameter: 19" (front and rear)

Wheel width: 10" (front and rear)

Wheel offset: +19 (front), +15 (rear) dish all around but more in the rear

Tyre size: 275/30/R19

Modifications: nothing....Front - spokes clear the front brembos by 1-2mm, full lock, no scrubbing. Rear - about 20mm clearance from top of rear tyre to underside of rear guard lip. Occasional scrubbing if I hit a pothole. Side wall of tyre comes past the rear guard by 3-5mm.

PB092908.jpg

  • 2 weeks later...

hey guys, i have an r34 gtt and want to get a set of grizzly import steelies but im hopeless with offsets and wheel sizes

they only come in: 16x8 -0 and 17x8 -0

16" is to small, so im gunna go 17", the question is will 17x8 -0 fit in my guards?

hey guys, i have an r34 gtt and want to get a set of grizzly import steelies but im hopeless with offsets and wheel sizes

they only come in: 16x8 -0 and 17x8 -0

16" is to small, so im gunna go 17", the question is will 17x8 -0 fit in my guards?

Try this offset calculator: http://www.1010tires.com/Tools/Wheel-Offset-Calculator

I would think 0 offset is way out there...

With that setup you are quite literally just moving the whole rim and tyre outwards by ~30mm. Honestly, I think it would fit but I would get your guards rolled as depending on the height of the car, it may rub. But if you are leaving stock suspension on I don't think you will have an issue. But you will be poking a fair bit, like 10mm outside the guard if you don't have aggressive camber setup.

(Form > function) If running a degree of camber or 2 is ok with you, run some stretch on the tyres and you could lower it to your hearts content (after rolling your guards) and you could pretty much have the chassis on the ground. It will be low and aggressive, if that is what you are after.

(Function > form) If you can go with a less aggressive offset (+10/+15) it would sit inside the guards flush, then you could run normal tyres.

For reference, I am running the same poke as the wheels you want to buy. I have stretched tyres on the front, and it lowered as low as it could go. And rears I have left decent sizes rubber on and left it a little higher.

I'm a bit hesitant about jumping into this discussion...

Remember the question is about an 8" rim. To get appreciable stretch on that you would need a 205 or 215 width tyre maybe which is smaller than a stock tyre. Each to their own and all, but it just seems a bit silly to me.

I'm a bit hesitant about jumping into this discussion...

Remember the question is about an 8" rim. To get appreciable stretch on that you would need a 205 or 215 width tyre maybe which is smaller than a stock tyre. Each to their own and all, but it just seems a bit silly to me.

Hence why I said he should reconsider the offset as the tyre size is way too small IMO. Easy for me as I am running 9.5s.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
    • When you pulled it off, there is no signs of blown head gasket? Is it possible you have some other issues going on? Possible cracked blocked? Or do you think it's straight up lifting the head? Did you check what the head was torqued to before pulling it down (To see if possibly they're stretching, or starting to break threads out etc)?
×
×
  • Create New...