Jump to content
SAU Community

Recommended Posts

also, 1 add says unknown k's then in the more expensive ad he boasts about the low kms, and even tells you that the dash was changed at 50k and now has 33k so it sounds like he knows the exact k's

he is also slightly negotiable....maybe slightly means $7k

It was advertised for 19.5K without rwc or compliance. But now claims to have been sold for 19K. I wish I could buy and sell a car that I don't even own that fast lol.

Nice pic in the ad there now:

http://firesport.ipspace.com/item_images/24585.jpg

Good on him!

If he was quick enough to be the first person to spot a bargin and then smart enough to make a $7k profit, in a very short time, good luck to him.

Having not read his ad, I just hope he/she did not bs to the person that bought the car.

Also details can be obtained after the car is bought.

Car was sold and has been onsold, it happens a lot with the cars we list (and mostly those that we don't list). We've got a few legitimate businesses that buy cars through us and then onsell it for a lot more, and some private individuals who do it to make some money on the side. What they do with a car after they buy it is none of our business, we get paid to find people cars and help em import it.

We actually had 6 people contact us within 1/2 hour of that email being sent out wanting to buy it.

PS. the limited edition R34 GTR was midnight Purple III. Still the R32's a sweet lookin car though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...