Jump to content
SAU Community

Recommended Posts

hey gary,

has anyone else experienced difficulty fitting front bushes into the stock clamps?

do you require a whiteline clamp as well to suit the bnf28 bar?

cheers

The Whiteline polyurethane D bushes are a tight fit into the standard D brackets. It has happened (very infrequently) that Whiteline have supplied the wrong D bushes with the bar. A couple of quick tests;

1. Try fitting one of the D bushes to a D bracket, without the bar in the D bush. It should fit easily, with only very mild distortion of its moulded shape.

2. Next try fitting one of the D bushes to the bar, without the D bush being in the D bracket. It should fit easily, with only a very small gap where the bush is cut.

If the above tests indicate problems, D bushes usually have a part number moulded into the flat side. What is it on the bushes you have?

:laugh: cheers :)

The Whiteline polyurethane D bushes are a tight fit into the standard D brackets. It has happened (very infrequently) that Whiteline have supplied the wrong D bushes with the bar. A couple of quick tests;

1. Try fitting one of the D bushes to a D bracket, without the bar in the D bush. It should fit easily, with only very mild distortion of its moulded shape.

2. Next try fitting one of the D bushes to the bar, without the D bush being in the D bracket. It should fit easily, with only a very small gap where the bush is cut.

If the above tests indicate problems, D bushes usually have a part number moulded into the flat side. What is it on the bushes you have?

:happy: cheers :D

Thanks Gary,

The D-bush i have has #1484/24 stamped onto top.

The bar that came off my r32 was only 20mm im not sure if that has created the problem or not.

I have managed to fit it with a couple of mods;

1- I ground down the top of the D-bush approx. 2mm

2- I then added 5mm spacers between the D-bracket and chassis

I also sanded off the paint which adds up to 1mm thickness

The bar fits in perfectly now, not too tight that it looks like it is binding up.

I couldnt start any of the bolts before!

Cheers

Thanks Gary,

The D-bush i have has #1484/24 stamped onto top.

The bar that came off my r32 was only 20mm im not sure if that has created the problem or not.

I have managed to fit it with a couple of mods;

1- I ground down the top of the D-bush approx. 2mm

2- I then added 5mm spacers between the D-bracket and chassis

I also sanded off the paint which adds up to 1mm thickness

The bar fits in perfectly now, not too tight that it looks like it is binding up.

I couldnt start any of the bolts before!

Cheers

The bush part #1484/24 is the correct one and I haven't had anyone else report issue like this. As I said, they are a tight fit, but your level of required mods seems excessive, 1 mm + 2 mm + 5 mm = 8mm too big, that's way over the top. I will have Whiteline check the dimensions of the 1484/24 just to make sure that there is no moulding error.

:) cheers :)

Bilstein Australia have received a small shipment of R32GTST rear shocks. Those guys with back orders, I will be contacting you tomorrow regarding delivery of your shocks. Thank you for being patient. Anyone thinking of buying a kit, my best suggestion is to get in now, they won't last very long.

:P cheers :happy:

Gary,

I haven't heard from you and want to confirm that I am on the list as I placed my order in December when there was only 1 rear shock left. I may be jumping the gun but I'm getting a little nervous as I haven't received a PM from you.

Thanks.

Gary,

I haven't heard from you and want to confirm that I am on the list as I placed my order in December when there was only 1 rear shock left. I may be jumping the gun but I'm getting a little nervous as I haven't received a PM from you.

Thanks.

PM Sent

:( cheers :mellow:

Any chance of the Bilstein/Eibach coilovers like in the S14/S15 groupbuys?

I.e. A more track oriented setup

Yes, just ask, plenty of guys have.

The reason for the S13/14/15 coil overs is to allow height adjustment. Which the Skylines don't need, as the additional cirlcip grooves on the Bilstein shocks provide that facility.

:( cheers :ninja:

Sorry all, I have been out of action for 3 days, somebody gave me a nice little virus. So the PM inbox filled up, but it has been cleared now. So if you could n’t get a message though over the last couple of days please try again.

For those that did get a PM in before the overflow, please be patient I will get to them all sometime today (or tonight).

:laugh: Cheers :rant:

I am off to Bathurst tomorrow for the 12 Hour race, the race team is running (not a Skyline) and I have to do my Team Manager thing. I will be back on Tuesday, so please excuse the slow responses to posts and PM's.

:pirate: cheers :ph34r:

Hi SK,

Been looking at this group buy for a while now.. Was wondering if you'd be able to do anything the same in New Zealand? Understand it's not probably the easiest but i've been looking for one of these setups for a while (I quite like Whiteline gear) even if I can get the Bilstiens revalved over here or similar.. Or any idea about freight from AU > NZ?

Thanks,

Scott R

is it possible to get a price on whiteline control springs to suit a soarer?

Same Group Buy price, $144 a pair plus $10 freight.

If you are contemplating using standard shocks & lowered springs, I suggest you have a read of this thread.

http://www.skylinesaustralia.com/forums/in...c=103158&hl

:laugh: cheers :P

Guest carasky

hi i am new to this forum and i was wanting to know how much it will be to get front and rear shocks and springs for my series 2 r33 skyline coupe. This car is a daily driver so i dont want no drift setup just something nice and tight wat do you recommend and how much i ready to purchase...thanks

hi i am new to this forum and i was wanting to know how much it will be to get front and rear shocks and springs for my series 2 r33 skyline coupe. This car is a daily driver so i dont want no drift setup just something nice and tight wat do you recommend and how much i ready to purchase...thanks

PM sent

:) cheers :thumbsup:

  • 2 weeks later...
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yeah i found that alot of parts can be wrong or "very" hard to get the real right one. I already bought some brakes years ago on me "old" GT calipers and they were wrong too 😄  I told them too. Even send them pictures...but they said "EBC catalogue has them on my car... So i dont know what their answer will be. I call monday them and let them know that they are really not on my car. If they were they would be already on a car...
    • Welcome to Skyline ownership. Yes, it is entirely possible parts websites get things wrong. There's a whole world of inaccuracies out there when it comes to R34 stuff (and probably 33 and 32). Lots of things that are 'just bolt on, entirely interchangable' aren't. Even between S1 and S2 R34's. Yes they have a GTT item supposedly being 296mm. This is incorrect. I would call whoever you got them from and return them and let them know the GTT actually uses 310mm rotors. Depending on where you got them from your experience and success will obviously vary.
    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
×
×
  • Create New...