Jump to content
SAU Community

Recommended Posts

That was a great read.....

Was waiting for someone to do a proper test....

Didnt have my mone on caltex tho.... I assumed Optimax was a touch better....

My own tests....

Caltex 98 - Car pinged its tits off (thought i must have got regular unleaded)

BP Ultimate - Car ran great 270km per tank (air fuel ratios were good)

Shell 98 Optimax - Car ran a little rough 300km per tank (air fuel ratios were bordering un safe)

So i generally use Ultimate or Optimax. I find when using Ultimate my bumper is heaps dirtier after a tank and believe this is due to Optimax being a little cleaner.... Also i drive my car the same all the time.... Average fuel consumption is the same every time.... 300 per optimax and 270 from ultimate.... Plus i can get 4cents off at shell.... So i try to get shell as often as possible... However im empty today so im gonna fill on Caltex 98 and try again.... Maby i just got a bum batch the first time????

Could be a bad batch, when Vortex98 first came out we had a car towed into work with half a tank of water after filling up on it.

  • Replies 62
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I guess this shows that fuel from differing companies do vary. The government says what the RON should be and there is a plus or minus fiddle factor. Also winter fuel has a higher RVP or DYPE to make your car easier to start. Of course in summer this is reduced so you don't have problems on hot days.Though govt regs are lowering these to cut back on the smog levels.

As you can see in the states of Australia the fuel will differ because of which refinery made it.

The other thing to remember that denser fuels tend to make you car run a bit richer.

The higher the RON or MON the higher it's resistance to knocking. Hi octane fuel in a car that doesn't have the sensors that our skylines have[ knock sensors, etc] will have no increase in performance .

I guess the water problem is one of those things that happens. service station tanks get condensation in them,etc.I won't use Mobil 1 oil because i bought a 5 litre container from Big w a few years ago and luckily I notice it had a lot of water in it. I rang the Mobil help line . They couldn't explain it.

I allways found that vortex 98 pinged my skyline very hard but as soon as i put Ulimate in it the pinging went away and the car went harder. I also found that Synergy 8000 SOMETIMES would make my car go noticably harder.

weid that Vortex came out on front - i have tried it many times and got the same result every time.

I wonder how much free fuel or how much money Caltex paid MRT ? =)

Interesting that for what seems to be a fairly thorough test (to the extent of getting some folks

with a van from Caltex to analyse the fuels) they didn't:

a) adjust mixtures so that they were exactly the same for all fuels. Given that Optimax

claims to be a denser fuel, I'd have thought this was important.

B) adjust timing to take maximum advantage of all fuels (timing _was_ adjusted, but not for

individual fuels).

If we accept that the results are a) accurate and B) relevant given the sampling procedure

(and there have been some arguments to the contrary earlier in the thread) then the

test shows that Vortex98 is the best bet for 'good power' on an untuned Ecutek in a Subaru.

I don't know that it follows that Vortex98 is necessarily 'the fuel' to use on a tuned car.

My belief is that 'the fuel' to use on a tuned car is the fuel it was tuned on, batch variations

aside.

I'd love to see a comparison where the same car was adjusted for the same

mixtures across a range of fuels, and the adjustments needed shown.

Then I'd like to see the mixture-corrected car adjusted for timing (with the adjustments

tabulated) and see power measured.

Then I'd like to see the tests repeated, monthly, for 12 months.

I'm dreaming :(;)

Regards,

Saliya

something else you might be interested to know

from the Federal Chamber of Automotive Industries website

http://www.fcai.com.au/ethanol.php/2004/03/00000001.html

"Nissan vehicles manufactured from 1 January 2004 onwards are capable of operation on ethanol-blended fuels up to E10 (10% ethanol), providing that blending of the ethanol component to the petroleum component of the fuel has been properly made at the fuel refinery (ie there is no "splash-blending" of the fuel).

For Nissan vehicles manufactured prior to 1 January 2004, Nissan Australia does not recommend the use of E10 because of drivability concerns and/or material compatibility issues."

regards

Jase

im still not clear about whether Ethanol is good for the car.

i remember they put it in a lot of petrols and damages engines.

theres new 'cheaper' petrol with ethanol (<10%) 98 otcane..

i just want to know, is this stuff any good??? or should i stay away.

if i could afford ultimate, i woudnt ask these questions...

The main concern with Ethanol is it's a solvent and can eat some types of fuel lines, but mate you drive a performance car, one that was designed to have a diet of Japanese super (100RON), tighten your belt and buy 98RON, buying lower octane fuel will only cost you a LOT more if you do engine damage because of it.

Siliya has hit the nail on the head. What happens when you lean out your mixtures? You get more power. All these fuels test to be similar RON, so advance sould be similar. The results that we are seeing is how close to the fuel that the ECU was tuned with, (which was vortex).

Overall I think the quality of the report is pretty poor. It looks to me like it's a draft that hasn't yet been scrutinised by the academics that should have been overseeing the testing.

eg

But why were they better? After consulta

Winter mix March 16th to November 14th maximum legislated amount is 90Kpa @40 deg C ?????????????????????

PAUL CHECK HERE.

Please refer Appendices and chart XXXX before reading this part!

If I was UNSW i'd be dissapointed that something like this was released. If I was MRT and they were asked to pay for this I'd be suitably unimpressed as well.

I'd even go further than what Siliya suggests and include ADR drive cycle testing.

Overall I think the quality of the report is pretty poor. It looks to me like it's a draft that hasn't yet been scrutinised by the academics that should have been overseeing the testing.

eg

If I was UNSW i'd be dissapointed that something like this was released. If I was MRT and they were asked to pay for this I'd be suitably unimpressed as well.

I'd even go further than what Siliya suggests and include ADR drive cycle testing.

If you go through the OCAU thread, u can see that this reports is actually an unfinished draft that was leaked.

I've heard some dyno operators in SA are recommending the ethanol blends for maximum power, but cars must be tuned to suit the fuel. Don't know how accurate these rumours are, so treat them with a grain of salt.

I don't think I'm game to try anything else unless I know for sure it won't affect longevity in my car. Ultimate is consistent for me, the cleanest of the lot, and I have enough power as it is at the moment :)

I wonder where SA gets its fuel from and which would be the most "fresh" fuel. Anybody know?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...