Jump to content
SAU Community

Recommended Posts

clean up the cut out part and practice on it?

they arent overly hard to set up, might as well practice on it, its only a 31, =P

yeah i've done a tiny bit of arc welding and i've got a tonne of rods (but no welder)

i don't think i could arc the 31 tho because the pannels must only be 1-1.5mm thick (rods are 2.5 so way too beefy)

anyone selling a cheap mig welder?

i belive you can hire MIGs at a pretty good rate.

like everything a cheap welder will give cheap results. a half decent one will do a good job with a bad operator.

dont get a gas less mig. may as well stick weld it.

Do like, the GT-C's will look mint ( if your still putting them on it )

Nothing really new on my car put on a new intake pipe ( stock one with a section cut out & filled with a piece of pipe ) as i found my old one had a rather large split on the underside

new pod ( +25kw :laugh:)

oil change & filter

just waiting till next week to register it and finish my pipes so i can have it all ready for time attack ( being a poser on the hill :sleep: )

c36020120308201745resiz.jpg

Edited by Autumn33

just a quick question, would having the wires to my tps cut have anything to do with why my car wont idle till warm? drives fine while cold just wont idle, only way i can get it to idle is unplug the afm till its warm. (just realised the plug has been cut)

Or could it be my acc valve?

Has all the tubes from the tb missing also but ive read that wont affect it.

Will be cleaning the acc tomorrow to see if it helps.

just a quick question, would having the wires to my tps cut have anything to do with why my car wont idle till warm? drives fine while cold just wont idle, only way i can get it to idle is unplug the afm till its warm. (just realised the plug has been cut)

Or could it be my acc valve?

Has all the tubes from the tb missing also but ive read that wont affect it.

Will be cleaning the acc tomorrow to see if it helps.

Dose your idle controll valve have a hose going into the cooler pipe work pre-throttle body?

The TPS has 2 sets of wires, one is the throttle signal, and the other is the idle switch. Your idle switch is cut, so your car will idle like shit. Also is the TPS isn't adjusted properly, the idle switch will never activate.

Edited by sav man

Dose your idle controll valve have a hose going into the cooler pipe work pre-throttle body?

For some reason i have a breather on the aac valve. Has a T piece with a breather and a hose that leads to a black plastic box :wacko:

Edit: managed to get my phone down there to take a pic, not the best but it shows what i mean about the breather & the black thing.

post-71390-0-27323600-1331469773_thumb.jpg

Edited by Autumn33

yep pretty simple. where that air filter is that line needs to be plumbed onto the turbo side of the throttle.

that would be sucking un metered air during cold start and idle. its a wonder it doesnt stall when you stop at lights.

that black box thing as you described is a heat activated air bypass valve. or cold start valve. its fully open when the car is cold and as the block warms up it closes off. it also has ignition power to it to help it close off. this is why under cold start imports rev heigh for the first few minutes then slowly go back to normal.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...