Jump to content
SAU Community

Recommended Posts

was just seeing all the threads on different gloveboxes - i just assumed they were all the same... and mine seems different again to all the other descriptions - mine opens from BOTH sides and is full depth for CDs etc... most other people whos open both sides seem to have posted that they are very shallow... weird so many different ones!

And yeah - factory Xenons with height adjustment for the high beam, controlled by a thumb-wheel on the dash to raise or lower the pitch down the road.

Edited by Brazen
I would have thought this test (fanging on a dirt road) ineffective because of awd?

hmm, you should still be able to tell - if you can't what is the point of having one! :P I haven't been on a dirt rd in my stagea yet (it does have the lsd as it is a four S), so can't comment from experience..

Ian

Wow that is cool!!!

My centre console storage space is NO WHERE NEAR that deep, and mine only opens from the front, it is hinged at the back, so it opens up like my old r33 did.

I never knew you could get it to open up from either side, cool!

I'll take some pics of mine on the weekend :P

Thanks Nick!!

Sorry pics took so long, but as promised here it is :w00t:

post-7853-1137106967.jpg

As you can see it is only like 2 inches deep, but when you reomve it to see what is underneath, it has this MASSIVE airbag thingy box directly underneath it, dunno wether that is where is is on stock cars though....?

It's a big silver box with cuation airbag stickers all over it and heaps of wires running from it towards the front of the car, looks like it belongs there as all the mounts for it are there and it actually sits raised about 1cm off the floor pan.

I'll take some pics when I can, dont hold your breath though :(

Owned :(

Airbag thingy? Is it an airbag or what? If it is, how the hell did they do that converting to manual

It is the g-force switch(if you call it that?) that sets the air bags off in your dashboard and steering wheel

Basically when you have a accident, the switch makes contact inside from the force of the impact and off go the airbags

It's a big silver box with cuation airbag stickers all over it and heaps of wires running from it towards the front of the car, looks like it belongs there as all the mounts for it are there and it actually sits raised about 1cm off the floor pan.

I'll take some pics when I can, dont hold your breath though :P

It is the g-force switch(if you call it that?) that sets the air bags off in your dashboard and steering wheel

Basically when you have a accident, the switch makes contact inside from the force of the impact and off go the airbags

It's most likely the computer with the g-sensors, as Darrin has mentioned. Don't forget, also, that GT-Rs (and probably GTS4s) had the g-sensors under the centre glovebox, behind the handbrake, and this was used as part of the triggering functions of the ATESSA computers. Seeing as most of us have RS-Fours, then they should all have them there, whether stock or converted to manual like mine and Ska's. I haven't bothered (or had the need) to take that part of the centre console off, so I can only assume they'd be in the same spot.

Who knows, maybe the same g-sensors were used for the airbags and the ATESSA!?!?

  • 2 months later...
  • 1 month later...
hey, i tried that, and i got pinged with a $99 parking in loading zone fine, they didn't believe i was on business, which i was... lowsy parking guys

A bit OT, but since when in NSW does it matter if your private rego'd or business.

It is my understanding that any wagon, ute, van or larger LR/MR/HR vehicle can legally park in a loading zone.

Alright, ignore what I said inpost #54, the airbag computer and ATTESSA sensor are separate items...

Airbag ECU:

Stageabits015.jpg

Airbag ECU (bottom of shot) and ATTESSA sensor (top of shot) with whole console removed:

Stageabits014.jpg

ATTESSA sensor just behind the gear shifter:

Stageabits013.jpg

  • 1 month later...

I would like to add a link to this thread in the "Stagea Diy's, How To's, & Fyi's" thread here:

http://www.skylinesaustralia.com/forums/in...howtopic=102808

And then unsticky this thread, any objections?

I think this is one thread we should leave exactly as it is now, we still have a lot of people visiting this part of the forums asking questions, and having it kinda hidden away makes it harder for those who are new to Stageas and are thinking of making a purchase or doing extra research.

I think the DIY section is better for us who already own them, and know to use it as a reference point when looking for instructions, etc. when we're doing repairs and/or upgrades. For any of those types of threads, then they could be put in the one DIY section...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • sold listed as a Tomei LSD 1.5 Way For 1998+ Nissan Skyline ER34 25GT RB25DE w/Open R200 https://www.ebay.com/itm/174006114594?campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=&mkrid=711-53200-19255-0&loc_physical_ms=108689&loc_interest_ms=&campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=71883f2ccc571356e0a757bc7adfdde2&mkrid=710-53481-19255-0&loc_physical_ms=108689&loc_interest_ms= it went in like butter all gears, alignment, back lash etc, rotation and clearances correct, and if rolling all rotates smooth and free when coasting down road , clutch in or out over 10 mph smooth... its the binding, clunking and jerking from a stop that is most concerning, also seems like its going to tear the tires off in 10 miles of normal road driving. 
    • What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...