Jump to content
SAU Community

Recommended Posts

Here are some pics of my final FMIC installation. I got the car back from Springy Motors earlier this week and am absolutely stoked with the outcome (see dyno thread http://www.skylinesaustralia.com/forums/in...t&p=4719149 )

I removed the front bar, as I wanted to replace the black mesh inserts to 'hide' the cooler a bit. You can see what the 'Cooling Pro' Stealth FMIC looks like behind the bar here. For $150 I had George at Springy Motors fabricate some brackets to allow the bottom cooler mounts to attach to the frame (the brackets provided in the kit don't attach to anything)

I hand-sanded the angle-grinder trimming behind the bar, and did a dry fit with the mesh held in with masking tape. I had to trim the cooler piping clamp bolts with a grinder to make some room, and when I was happy with the dry-fit, used some 'Sikaflex' glue purchased at Autobarn to fix the mesh in place. I put a few bricks on it overnight to make a good bond.

I then trimmed away excess glue, re-attached the front bar, and did up all the bolts holding all the undercarriage plastics in place. All in all pretty happy with how the whole thing turned out. It looks pretty tidy, and turned out to be quite 'stealthy' after all. My advice for anyone considering a Cooling Pro Stealth on a S2 would be to just budget around $150 to have it professionally fitted - you'll still be a whole lot in front of buying a Greddy kit!

post-52103-1247992138_thumb.jpg post-52103-1247992383_thumb.jpg post-52103-1247992706_thumb.jpg

  • Replies 254
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Looks great Tommy. How much did you have to trim off the front bar to get it all to fit??

Hey Sabbai,

I would estimate I trimmed about 60-70mm from the inner vents. Basically, (on a 'Dayz' bar anyway) you need to make the inner two vents flush with the outer vents. I'm not sure why the inner vents extend further into the engine bay than the outers in the first place, but they've gotta go. You could trim a bit more off to allow a bit more room, but I didn't want to make those vertical 'struts' either side of the numberplate any thinner than required.

PS

Very nice install Tangles! That looks seriously tough.

Hey Sabbai,

I would estimate I trimmed about 60-70mm from the inner vents. Basically, (on a 'Dayz' bar anyway) you need to make the inner two vents flush with the outer vents. I'm not sure why the inner vents extend further into the engine bay than the outers in the first place, but they've gotta go. You could trim a bit more off to allow a bit more room, but I didn't want to make those vertical 'struts' either side of the numberplate any thinner than required.

PS

Very nice install Tangles! That looks seriously tough.

Thanks Tommy. My Dayz Edition arrives late August and I'm wanting to get a cooler into it, but I didn't want to hack the front bar up. I like the way you've fitted it, as it looks to be done very well.

Looks good Tangles.

This is how i did it. I cut 1cm out of the lower part of the front bar, and got no problem at all with the clearance. :devil:

662460_ygzpf6.jpg

662463_4qhl67.jpg

664309_w7jyjc.jpg

664327_qtu2jz.jpg

Nice install guys ..... just thought I would say to all stagea owners thinking of putting on a big front mount I/C

Take note !!! make sure your radiator is in good condition!!! get it cleaned or fixed!! as stagea's and r33's only have a standard 1 core radiator!!(many other sports cars have three or four core radiators). And if radiator is half full of junk(As japanease dont like putting coolant in cars) it is alredy putting stress on motor/cooling system then if you reduce air flow with a front mount then overheating/extra/engine stress could result blown head etc or worse big $$$ So for the cost of around a $100 or so to get your radiator rodded/ cleaned out it's cheap and could possibly save you heaps. Just trying to save stag owners $$$ Trust me fixing head gasket on stag is a F***Bitch of a job. Stag on!! ;)

Total cost below 5000sek (approx 750 AUD)

Hey guys,

just thought I'd add my (Very recent) experiences on the front mount issue. I ordered a Just Jap "C34 Stealth" kit on Monday, received it very happily on Wednesday. To start of with, the front mount is now fitted and looks fantastic. The car boosts stronger, faster and higher, or so it feels :blush:. Fit of pipes up to stock set-up was absoloutely perfect, and the core looks a treat. The one gripe I have with the kit was the fittings (Silicon was fine. Hose clamps were great though!). To be honest, the brackets and fixings supplied with kit fit absoloutely nowhere. For example: It was necessary to add another 40mm to the supplied spacer lengths in order for the intercooler to sit off of the fan unit. This in turn meant I had to replace the supplied mounting stud with a longer unit to suit the new spacer lengths. When pairing the supplied nuts with bolts of same diameter, some of the nuts would not thread onto the bolts, any of them. The supplied brackets seemed to attach to nothing whatsoever, in any configuration (Nth to Sth orientation vs. East to West orientation.) which meant I need to purchase new angles and fabricate them to suit the application. To tell you the truth, the problem solving process and fabrication was an entertaining surprise, but not an anticipated one :P

In short, if you purchase the same JJR C34 Stealth Intercooler Kit, expect to:

-Buy new fixings, spacers and brackets: ~$50

-Extra fabrication time: ~1hr

N.B.: This was fitted to a 1998 Series 1 Stagea, "Dayz Edition". No trimming of the Front Bar was required :down:

Big thanks to Chris for the 8mm driver and his time tightening clamps and fitting the bar!

harts.

  • 1 month later...

Nice work Tangles! That cleaned up pretty nicely after the gaping hole I saw in the bottom of your front bar at a cruise once, and the intake pipes held in with cableties! That's a very nice looking Stag.

PS Where did you get that lower-lower-lip-spoiler?? That's awesome

Edited by DaveB
  • 5 weeks later...

Here's mine after throwing on the Blits front bar + sideskirts, and a HDI GT Spec R32/33/34 FMIC.

As will most coolers I had to do the following:

Cut a hole in the battery tray,

Trim the fan blades,

Cut out 2cm of the intrusion bar

Trim a fair bit of the front bar.

Create slightly larger holes where the factory piping went through (under the air filter)

I didn't move the transmission cooler, but if I relocated it, the cooler would most definitely sit better.

post-9646-1254113248_thumb.jpg

post-9646-1254113278_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hey guys, Just want some advice on r34 GTT ac system. Since I’ve owned it, the ac compressor, doesn’t matter the set temperature or ambient temperature, runs for around 10 seconds then disengages the clutch, then re-engages everywhere 30 seconds or so and keeps repeating this.    is this normal?   I had it recharged today as it was slightly low and thought it would fix it but still does it. it cools fine in summer even prior to the recharge, except for the usual warmup when stopped or in traffic (still yet to wire overheat fan to on with ac)   any thoughts would be much appreciated 
    • To plug the hole. The engine plant may not have known whether the car it was going into had a gauge or not. It was a long time ago and the integrations might not have been fully modern. Or they might not have cared because the extra inventory and processes to save a few cents on the sender might have cost more anyway. But please tell me you are not still confusing the idea of a pressure gauge sender, and an oil pressure light switch. The switch will be out there. In a separate hole. Probably with only one wire running to it. Running the light.
    • Blower needs to go low on the exhaust side, displacing the AC and PS, which you have to decide whether you want to keep and how and where to relocate if you do. Electric option for PS is, at least, helpful. Sadly, there is no workable 12V electric AC of any value. Whilst the blower is the last compression step before the throttle, and so it might seem a good idea to have it near the inlet manifold (as mentioned above), you probably want it to go through an intercooler first, so, having it on the opposite side of the car facilitates that air flow path. The turbo discharges into the blower, so proximity of the turbo's compressor outlet to the blower's inlet is nice. But then you might want to intercool that too, before boosting it again....which would probably be a ball ache. Routing pipes out to the front and back could be a bit shit. If there was room for (at least) a small (but preferably larger) water to air core on that side, then that would probably be the best approach. I guess a reasonable alternative would be to locate the blower where the alternator is (more or less, associated with the inlet manifold, per Matt's thought), and somehow incorporate a water to air core into the manifold, sort of like they do for modern blown V8s. The big difference here though is that those V8s have only the one throttle (upstream the blower) and only the one compression step (the blower) and no need for too much in the way of bypass/blowoff valves. Whereas in a twin charged 6, you do need to think about one or two bypass valves associated with the 2 compressors and you would prefer to have the intercooling done before the air has to pass through the throttle. You'd like the throttle to work approx the same no matter what the compression is doing. But if it is located in hot air stream before a cooler, then sometimes the air will be real hot, sometimes it will be quite cool, and the throttle mapping/response will be quite different between those two cases. The throttle, if sized for hot air, would be too large for cold conditions. It's all a ball ache.
    • Package SC on exhaust side. Remote mount turbo. Still a fair bit of room when you get creative on the inlet side of the motor too. Especially if you can get really creative with the welding, and effectively build it into the bottom of the inlet manifold. Would definitely take some design work, and some trial and error, to make sure flow works well still! Might be easier to just start with the Nissan March though... All the work is already done for you...
×
×
  • Create New...