Jump to content
SAU Community

Optimax Extreme (100ron + 5% Ethanol)


Zahos

Recommended Posts

Ferrari Ferrari does not recommend the use of ethanol blend petrol. E10 may be used in emergency situations.

Hmmmm ferrari know somthing and for nissan

Nissan vehicles manufactured from 1 January 2004 onwards are capable of operation on ethanol-blended fuels up to E10 (10% ethanol), providing that blending of the ethanol component to the petroleum component of the fuel has been properly made at the fuel refinery (ie there is no "splash-blending" of the fuel).

For Nissan vehicles manufactured prior to 1 January 2004, Nissan Australia does not recommend the use of E10 because of drivability concerns and/or material compatibility issues.

found at http://www.fcai.com.au/ethanol.php/2004/11/00000001.html

Link to comment
Share on other sites

  • Replies 168
  • Created
  • Last Reply

Top Posters In This Topic

TECHNICAL REASONS FOR INABILITY TO USE E10

The following are reasons why certain vehicle models cannot or should not use E10 because of material incompatibility and driveability issues respectively. There are also comments on possible exhaust and evaporative emissions issues. This list was compiled from information submitted by manufacturers.

CANNOT USE BECAUSE OF MATERIAL INCOMPATIBILITY ISSUES

Early deterioration of components in fuel injection system:

Fuel tanks

Fuel lines/hoses

Injector seals

Delivery pipes

Fuel pump and regulator

Vehicles with carburettor fuel systems may experience hot fuel handling concerns and may experience a lower level of durability in some fuel system components.

Some manufacturers advise not to use E10 with any model equipped with a carburettor because of material incompatibility.

SHOULD NOT USE BECAUSE OF DRIVEABILITY ISSUES

Vapour pressure of fuel with ethanol will be greater (if not chemically adjusted) and probability of vapour lock or hot restartability problems will be increased.

Oxygen content of ethanol is 34.7%. This can cause the engine to run lean although the Engine Control Unit (ECU) can generally compensate via feedback from the O2 sensor under light throttle conditions. However, hesitation or flat-spots during acceleration can occur due to this lean-out effect.

Difficulty in starting and engine hesitation after cold start.

EXHAUST AND EVAPORATIVE EMISSION LEVELS

Lean-out resulting from the oxygenating effect of ethanol in the fuel may affect exhaust emissions.

Fuel containing ethanol can increase permeation emissions from fuel system components.

Vapour pressure of fuel with ethanol will be greater (if not chemically adjusted at the refining stage) and can lead to increased evaporative emissions.

Link to comment
Share on other sites

Only problem is we're not talking about E10. This is only a 5% mix which is half of that.

You should not run E10 in your skyline because it is not a 98 ron fuel.

The only fuels you should ever be running are Shell Optimax or BP Ultimate. Don't even worry about the E10.

Link to comment
Share on other sites

You should not run E10 in your skyline because it is not a 98 ron fuel.

Not quite true - can get 'Boost98' here in Adelaide, 98ron with 10% Ethanol. Tried half tank of boost98 with half tank of BP Ultimate, seemed ok. 'Felt' different though........

Link to comment
Share on other sites

To start with, I've been running on Optimax 98 for the last 5 years so I know what my car is like under all conditions with that fuel. Also, I run a pretty rich A/F mixture normally ( if that means anything in this comparison ).

Well, I chucked 20L of OE100 in yesterday early arvo and have since put 60km on the car. First thing I noticed was a slightly different smell from the exhaust and after about the first 10 km's it started idling a bit better. I've since opened her up and gone for it ( paying carefull attention to any pinging etc ) and it goes as well ( if not a little better ) than it has in the past. So......I think I'll continue to roll with the new Extreme 100 for a while and see what happens :P

B.T.W. RB20DET w/ Arias Forgies, 550cc injectors, HKSGT2535, Chipped ECU, 1.2bar boost.

Link to comment
Share on other sites

cc, it is the fuel companies that have been using their contacts for years to keep competition from ethanol away....I bet the combined fuel companies have more political clout than some cane farmers

Good point .. for all my counter counter counter culturing I forgot to think about that - looks like I'm a pleb afterall.

Having said that cane farmers have never been a fan of the liberals, and the nationals have been a coalition limp dick for a long time... and that guy who owns the ethanol plant is one of the biggest donators.. and him and howard have met numerous times... I don't know I suppose anything is possible but I'm inclined to believe Howard and mates are at it again.

hang on, its more expensive because Shell are selling it as a premium fuel.

it has nothing to do with the price of ethanol or govt taxes.

the point about ethanol is that it is cheaper than petrol.  It is up to shell how they use it from there.

I haven't used it yet, but fully intend to.  I think the ethanol issue is being *way* overplayed in this thread.....it is 1/20th of what you are buying = bugger all.

It seems that fact that shell have oxygenated the fuel is having a much bigger impact than the ethanol content.

*edit* yes it is shell not BP :P

Ethanol is more expensive to sell in Australia because the government whacks the fuel tax on it. If the government really believed in the globalist ideal of unilateral free trade Brasilian ethanol would be the place to get it from - this is also substantially cheaper than Australian ethanol (so much so the government tariffs it till it's uneconomical to buy).

Also - will you be doing anything to your fuel systems to run it or is that all silicone/braided stuff anyway?

I may try a tank for a track day where the octane rating will protect when pushing the car constantly, but also where it will be used in one go as opposed to sitting in my fuel lines for a week.

Link to comment
Share on other sites

I filled up with the optimax extreme and my gtr has been running awesome, after filling up a drove it home and in the morning reset the ecu and let it remap.... and it hasnt run this well in ages, seems to pull harder accelerate smoother.... its been really good!! just my 2cents, and also i seam to be using less fuel than usuall, so im all for it!!!

Link to comment
Share on other sites

I tried it today on my 33 gtst, was a little hard to start first go, and then hunted around for a while before it idled. It has since been rock solid and starts perfectly. In terms of performance it feels quite responsive, especially throughout the midrange, but I could never be certain without chucking it on a dyno.

I wasn't too concerned about running lean as I have a rom tune that is rich with advanced timing... (I couldn't hear any pinging today) but I do believe it leaned the ratios a little as I am now sans most of the crackles and pops that come from the exhaust.

I also found it quite amusing that there was a shell rep waiting at the bowsers, handing out brochures for OE100 to everyone, and telling them that this "wonderful new fuel will clean their fuel systems"

Link to comment
Share on other sites

I have used both Boost98 from Liberty with 10% ethanol and Optimax Extreme 100 with 5% ethanol.Car ran great with both,couldnt pick a difference.I'll probably stay with Boost98 because it is available at far more Service stations,is about 12c a litre cheaper than Extreme and a good power gain has been documented.If Extreme proves to be a better fuel,I will change as long as it is available at more outlets,I get 3 tanks of petrol a week,cant be hunting around all day,as there are no outlets near home or my office.

Link to comment
Share on other sites

I filled up with Optimax Extreme to give it a try, and did not have any problems at all so far. Be it starting, idling, hard acceleration, normal driving. I have a remapped stock ecu(done in japan).

Generally i find it smoother, better throttle response and im able to move up the rpm range with lesser effort on the part of my foot. No knocking so far.

Just my experience with it so far.

Link to comment
Share on other sites

E10 melted my injectors on my old R31. after the second tank the car was having issues with leakng fuel down the block i assume when the R33's and R32's get a little older they may face the same issues

Nah, that would just be the most common problem that the RB30 motors had. Leaking injectors and injector hoses.

Link to comment
Share on other sites

I haven't read all the post about this stuff ( so this will prol sound real stupid ) but does Ethanol have anything to do with Sugar Cane ? When I was filling the tank I could smell something that I couldn't identify until yesterday arvo and I'd swear the smell is Sugar Cane !!

BTW, drove in this morning ( cool temps ) and the car went like a rocket !! It seems to like the taste of OE100 :)

Link to comment
Share on other sites

I filled up with Optimax Extreme today, and did not have any problems at all so far. My engine is a RB25DE with stock ecu.

I find it smoother, better throttle response and im able to move up the rpm range with lesser effort on the part of my foot. No knocking so far.

Link to comment
Share on other sites

I've run 2 tanks through the GTR since I discovered it..

I've noticed the following difference in the cars performance changing from optimax/bp ultimate:

Keep in mind my car was already running very rich on 98 RON fuels.

- no more popping! the car does not pop at all anymore. previously it was running quite rich and popping about once per gear change

- the car is a lot smoother

- the engine is more quiet

- the car pulls a lot better

Cheers.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I’m sure this has been discussed many times. But anyone have any or know someone that is selling genuine N1 rear pods? I’m still shocked no one replicates these yet. Looking to buy some. Added a photo of the part. 👍🏻
    • Hello, The dog bone wont have much to do with this - the calliper applies a load about the disc - the outside of the calliper is more flexible than the inside by virtue of it not haveing the big torqued down bolts, additional metal structure on the caliper itself, and mostly not being cantilevered. So the outside of the calliper is pushing away as its more bendy and brining the inside with it as an equal pressure on both sides of the caliper looks to cause more flex on the outside - which makes sense. I have done this same thing with the calliper unbolted from the dog bone - same thing happens. Although id have to watch more carefully to see how much more the outside moves than the inside in this case. Im guessing there is a point in the pedals travel where the pressure is not actually increasing in the system - its just volumne displacemnt - and because the outside of the calliper is more flexy, it receives that volume. Have gone back to Alcon again - but beyond a resolution there I would stay clear of this calliper and possibly any of the lighweight type of callipers - especially if you have the smaller 15/16" master cylinder. Cheers.
    • Yes, you can very clearly see from more than one angle that it is the whole caliper moving left-right, not deformation of the caliper. The top moves, the bottom moves. Equally. It should be possible to see where the movement is occurring. Just need to look more closely.
    • Hi Folks, my 2009 Skyline 370GT “Crossover” wagon is losing water and has been diagnosed as needing a water pump replacement (it’s an internal timing-chain driven unit, not the usual electric type that seems to be used across many manufacturers). Am looking for any repairer recommendations in the Sydney /Wollongong region who can be trusted and are experienced in this sort of work on the VQ 36 engine. Many thanks….Bill
    • While all of the above makes sense, we're not talking about some Ling Long calipers of AliExpress; Alcon would have to be one of the top 5 caliper suppliers in the world and these are not their budget units. If there were manufacturing defects in the caliper causing this issue I'd be very disappointed. Having re-watched the video a few times I think it's dog bone/mount related. The caliper moves independently to the rest of the suspension and brake assembly which suggests to me that it's not mounted rigidly. I know this sounds stupid, but have you got enough thread on the retaining bolts or are they a poofteenth too long and it's not super tight? For axial movement to be occurring without deforming the caliper that can be the only answer.
×
×
  • Create New...