Jump to content
SAU Community

Recommended Posts

  • Replies 75
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

if you get a good one it will be quicker stock for stock than a 33gts-t, also stock for stock they handle better IMHO.

harder to work on than skylines but not too bad, with a lot of similar stuff in them. just remember most of them are a lot older than say r33's (which people seem to compare them too) so the age is the cause of a lot of things going wrong since most of them are 89-93 models. interior is also an older design when compared to an r33.

Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1721697
Share on other sites

Same as ^^^^

Mate with a 90 TT Manual

Did the 100k service on it.

Were that frustrated by the end of the 7 hour stint that we could have killed someone.

Wost car in the world to work on.

Repairs are very costly as every single part is hard to get to.

Turbos are an engine out job if you ever blew one or wanted bigger.

They are very heat happy and without sufficient cooling they over heat.

Main problem is the heat damagge that the components cop with every rtadiator fan and clutch peice i have seen on a 300 in need of replacing.

can boost to 13-14 psi by simply buying 2 $3 welding tips with a .9mm hole

The power output is crazy with very minimal mods.

Do buy a 5 speed though you wont regret trying to find one :)

With boost ,exhaust pod and safc II tune he has 338rwhp with 14 psi

Edited by Slide
Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1721738
Share on other sites

very hard to work on. Things that are basic on most cars are a pain in arse on zx's. it gets to the point where it seems like the engine has to come out to do anything. and i dont really like the look of em either :)

Edited by RRR32_GoDzIlLa
Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1721774
Share on other sites

After having a drive in a manual TT, I agree with the car's owner who said they make a great cruiser. Loads of power available, nice handling, but don't buy one and try and drive it like a WRX.

I love the cockpit. Almost as good as an R32. It was Nissan's attempt to produce a car marketable in America against Corvettes and the like.

Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1721841
Share on other sites

cons

overheating issues

biggest myth, as long as it has been even half decently looked after.....

Oh.. and although people say it's heavy, it's no heavier than a line....

former owner.... cant wait to get my hands on another.

The cons are that it's very tight engine bay. very hard to get your hand in anywhere around the block.

also you don't want to trust just anyone with repairs/mods/servicing as most people cant even find the air filter, so it will cost abit to get anything done on it.... my recomendations are Unique auto sport in castle hill, they are Z specialists, so they know what they are doing... but it will cost abit.

great car.... i've got nothing but praise for it.... check out Aus300zx.com for info on what to look out for when purchasing one....

Edited by Archie@
Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1721843
Share on other sites

What is it with people's obsession with being "different", at the expense of logic and reason?

I'm not necessarily saying that a Z32 is a bad choice, but "spending extra every time" for no appreciable gain (aside from this insecure need to be "different") just strikes me as a waste of time and money.

If you truly wanted to be different, get your hands on an R34 coupe shell and do a CA18DET conversion out of a Nissan Exa. You don't get any more different than a FWD Skyline with a 4 pot, so you can brag to all and sundry about it.

Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1722504
Share on other sites

I think that the Z32 is a nice car if you want a grand tourer. Its got plenty of poke, and its cabin is quite a nice place to spend time.

And yes, it does have a reputation for blowing things up so much that writing about all the ways in which they could fail would probably get you arrested under the new anti-terror laws.

And while yes, if its been well maintained it'll be OK but then that's true for any car. Even something as breakage-prone as a pre-Ford Jaguar will generally not shed bits if its been "maintained". The question is, if the average person owns one and treats it like a car, rather than with the loving tenderness akin to their own genitals, will it fail?

Not every Z32 was bought by people who took great care of the cars. You had a lot of mid-lifers who bought them as a status symbol rather than performance, then you had a lot of young people who had to stretch to afford it and couldn't afford to maintain it.

And, in those circumstances, the Z32 TT tends to be a lot less reliable than most. Such a cramped engine bay and all that heat adds up to mechanical and electrical failure. The cars are also getting on, and any work is a major effort.

Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1722511
Share on other sites

Freshly imported z32 5spd tt's  for 10 k comlied and registered though.

If that isnt bang for your buck i dont know what is

If the car's your typical 10-15 year old thrashed out Jap import with an unknown service history, you'll certainly get a lot of bang.

Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1722524
Share on other sites

When i was chosing a car, 300zx tt was on the list, and knowing diddley squat about cars and the such, one thing i could tell.

Pop the bonnet and look how cramped it is!

Jeeeeeze!

You can tell that if anything needs to be done, it'll be a job and a half.

On the other hand, i reckon they look fantastic! Was good to see it in Kill Bill too!

Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1722818
Share on other sites

they dont overheat, its just that the heat in the engine bay takes its toll on other components.

Reminds me of that quote from Collateral:

Max: You killed him?

Vincent: No, I shot him. Bullets and the fall killed him.

Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1723218
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...