Jump to content
SAU Community

Don't Take Your Mum's New Camry To The Track.


Recommended Posts

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

Ohhhh!!!! So *THIS* is where I've been going wrong!!!

You're supposed to downshift AFTER corner entry and straighten up your line BEFORE the apex and then jerk the steering wheel back.

He just didn't do anything when it started to let go!! ahaha.

LOL - that's exactly what I was thinking when I watched it. He may as well have been sitting in the passenger seat once he lost it.

Also had to laugh as I have that exact same helmet, so it's a bit of a worry!

yeah this has been posted a few times since it happend. I think his main problem was he took two big bites at the corner, and down shifted mid corner for some reason. I actually feel sorry for the poor guy, i mean he was at a driver training day. he just made a mistake due to his inexperience and was unlucky enough that there was a pond on the inside of the track. i still don't know what track they were using as that's the issue i have. it doesn't look very safe at all. it looks more like a road with some witches hats randomly placed...

Bo hoo hoo i lost mummys car in the itty water.Lol.

He downshifted/ or poped the clutch mid cnr,but only after the car was allready in a slide,which was probably started from the wrong gear selection and not enuff brake in the first place. :P

Cant wait to meet up with you guys in a few weeks and put some names to faces.I just had the blue slip done so!!!

Let me tell you.It was allot of faRt asSing arrounD.

and was unlucky enough that there was a pond on the inside of the track.

That pond would have done less damage than a concrete wall trackside. He would have written off the car and compacted it into a cube had he blindsided a concrete wall instead of having that run-off area and a pond to slow him down :lol:

Dry off the car, use a borescope and make sure no water was ingested and his mum would never know the difference :P

That pond would have done less damage than a concrete wall trackside. He would have written off the car and compacted it into a cube had he blindsided a concrete wall instead of having that run-off area and a pond to slow him down  :lol:

Dry off the car, use a borescope and make sure no water was ingested and his mum would never know the difference :P

yes that's for sure! My friend would agree. he lost control of his GT3 cup car at turn 1 EC and i'm sure would have preferred a qucik bath as opposed to the concrete wall he hit. but my point was that place didn't really look like a race track at all. there were close trees lining the outside of the first corner. it just didn't look right.

It's Darlington Park, QLD... and yeah, it's a Corolla.

Corolla%202.jpg

I feel sorry for the guy, he's taken it to the track to try and learn more, and obviously has made a mistake and then panicked.

It's very easy for easy to see exactly what he did wrong from the comfort of our computer chairs (or couches if you've got wireless :P), but in the moment, i'm sure some of us when learning to drive could have made the same mistakes, especially if we panicked.

Cheers,

Tommo.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...