Jump to content
SAU Community

Best Way To Use Carby Cleaner

ICER33

By ICER33,
in General Maintenance

 Share

Recommended Posts

Panikin Collaborator

Panikin

Posted
Posted

I would suggest using electronic cleaning solvent for the afm as it is a fairly sensitive hot wire element in it, spray it leave it for 10 min and do it again just to make sure its cleaned properly wait 10 min before driving . It works a treat as I have used it on both of my cars & my sisters atmo R32

satanic Grand Master

satanic

Posted
Posted

Questions:

How far away do you spray from (don't want to damage the element)

Do you only spray the element or the inside of the AFM casing as well?

How do you know when it's clean? Do you shake it around and watch crap fall out?

raz0r$harP.UK Grand Master

raz0r$harP.UK

Posted
Posted

Depending on how much oil there is in your intake pipe you may wish to spray with your AFM still attached. Generally I just remove the AFM and clean it separately. You can always remove the intake piping and clean it off the car if you want.

Run your finger around the inside of the AFM. If it's oily, then it could probably do with a clean too.

I use CRC Contact Cleaner. Hold it about 15-20cm from the AFM, and spray in the direction that air passes through. May need to give it a few blasts if you have a lot of oil.

Once it dries (about 30 sec) you should be able to run your finger inside and see that it is clean.

You shouldn't see stuff fall out of it. Generally oil will just stick to the element and the inner plastic.

  • 2 weeks later...
someonestolecc Grand Master

someonestolecc

Posted
Posted

Thanks, I've always wondered :D

but wtf is the AFM

Air flow meter - it basically measures how much air passes into your engine. It's the main input for the computer and a hell of a lot of decisions are made based on that input. Basically if you find the air filter in your car and follow the pipe a little back you should see a piece of "pipe" with some flanges on it and a plug coming out of it. That's your AFM.

Duncan Grand Master

Duncan

Posted
Posted

Don't use Carby Cleaner on the AFM it leaves a residue afterwards. Use Brake Cleaner or Electrical contact cleaner instead.

Do it on the car if you can get to it, just spray the actual senor wire the rest of the assembley doesnt matter.

Weasel the AFM is after the air filter it is a piece of wire and plastic sitting in the middle of the intake pipe. If it gets dirty it can give incorrect readings to the ECU resulting in missfires

Neil Grand Master

Neil

Posted
Posted

What Duncan Said,,,"Brake Cleaner". It's my mechanic in a Can. Cleans AFM's,,,funny enough brakes (removes spilt brake fluid as well as cleaning brake grunge. This stuff SHOULD be in everybodies toolkit.

I even use it to clean up his oil seepage between races.

If you really want to do a test,,,get a clean piece of glass and spray some carby cleaner,brake cleaner and contact cleaner on it, one at a time and you tell me the results.

Neil.

  • 3 weeks later...
hijaked Collaborator

hijaked

Posted
Posted

haha. when i cleaned my AFM i used CRC contact cleaner. didnt need much, endded up taking it back. scored $20. booya

i cleanded it too much, long story short. my car was running better when the AFM was dirty (as my car was rooted). so for no reason i decided to try dirty it again... used everything i could find under the sun, as long as it was spray-able. however it wouldnt go dirty again.

anyways got my initial problem fixed and now the car runs fine, with my poor attempts to dirty the AFM.... id clean it again if i didnt have to go back to the shop to get a can of cleaner

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...