-
Posts
173 -
Joined
-
Last visited
-
Feedback
100%
Profile Information
-
Gender
Male
-
Location
Northern Rivers NSW
-
Interests
Cars R/C Models Amateur Radio Electronics
Profile Fields
-
Car(s)
R33 gtst VK Waggon
-
Real Name
Sam
Recent Profile Visitors
7,324 profile views
Dasmbo's Achievements
-
Dasmbo started following oil pump , 33 GTR Broken front wheel knuckle , R33 GTR RB26DETT air whistle at 250Km/h and 7 others
-
33 GTR Broken front wheel knuckle
Dasmbo replied to believer's topic in RB Series - R31, R32, R33, R34 (1986-2002)
Never seen this happen twice i would guess parts taken beyond manufactures specks if it were me i would have the next knuckle joint shot peened to try and make it stronger just like you would have your con rods shot peened good luck with it -
R33 GTR RB26DETT air whistle at 250Km/h
Dasmbo replied to Tomak's topic in Forced Induction Performance
Didnt know GTR's came in left hand drive and my 1995 gtst is very quiet with just the turbo whine rear wing bending towards the bootlid at 200 plus kms but my car does have a full complete set of door Boot rubbers installed a few years ago -
Hi i wouldnt wast my time trying to get more boost out of your stock turbo because if the inlet wheel disintergrates into a few hundred peices and exits the manifold into the engine causing lots of internal damage not to mention the shock to your wallet.With something like an Hypergear turbo which are not to expensive you wont have to worry about a stock turbo disintergrating and destroying your engine. I have been using a Hypergear turbo on my setup for the past 10 years with no problems and consistantly makes good power.
-
Freshly Rebuilt rb25det no compression!!
Dasmbo replied to Driftieboy's topic in RB Series - R31, R32, R33, R34 (1986-2002)
Hate to be the bearer of bad news but it sounds like it is going to cost a lot of money even a stuffed motor has a bit of compression. -
Is this rb26 block useable for modest build?
Dasmbo replied to hixzoomy's topic in RB Series - R31, R32, R33, R34 (1986-2002)
GTSBoy is spot on its only use is a boat anchor any money spent on it would be pure waste cut your losses before you start -
The ever evolving R32 GTR build
Dasmbo replied to mr_rbman's topic in Projects, Overhauls and Build-ups
Some battery places should be able to smelt on a new battery post for you -
Problem noise sound
Dasmbo replied to BrownieIT's topic in RB Series - R31, R32, R33, R34 (1986-2002)
About 3yrs ago the timing belt shedded on my VK holden RB30/25 reason unknown belt replaced no problems since also have a r33 RB25 and never had any problem with it i mostly answere question in which i have had personal problems with VK i have had for 27 years r33 had for 15 years so i have done a lot of kms with them -
Problem noise sound
Dasmbo replied to BrownieIT's topic in RB Series - R31, R32, R33, R34 (1986-2002)
Use a long screw drive or something like on and use it a a stethescope and press it on to several different parts of the front covers to determine where the noise is coming from it does sound like some sort of interference of one of the front covers. What condition is your timing belt in hope its not starting to desintergrate as i dont know what condition your engine is in and how many kms it has done for the engine all of a sudden starting to make this noise i would be removing the top cover and inspecting that space and rotating the engine to inspect the belt because if it breaks you will need deep pockets to fix -
I was wondering as i was thinking of rebuilding another engine for my vk holden i currently use a nitto pump in my r33 was just wondering if anyone had any info on them
-
Hi i have seen ads on ebay Speedmaster RB30 Billet Oil Pump w/ 4340 Billet Gears has anyone tried these pumps and are they any good i have seen them for sale elsewhere for over a thousand us dollars
-
viscous diff replacement for R33 gtst
Dasmbo replied to Dasmbo's topic in RB Series - R31, R32, R33, R34 (1986-2002)
Hi thanks i will contact them tomorrow -
viscous diff replacement for R33 gtst
Dasmbo replied to Dasmbo's topic in RB Series - R31, R32, R33, R34 (1986-2002)
Hi im here again to try and find some information before i go and spend my hard earned buck purchasing the bits needed to upgrade my single spinning viscus diff to a cusco kaaz nismo centre is there any shops in the south east queensland or north eastern new south wales where i can take my diff and have the parts fitted and setup like preloads set etc as i would also like to replace the pinion bearings and front seal. Does anyone know where i can purchase new pinion bearings and seals so far i cant find anywhere who stocks them or there part numbers. I would be grateful for any information so i can get full throttle and traction again