Jump to content
SAU Community

blind_elk

Members
 View Profile  See their activity

  • Posts

    6,948

  • Joined

  • Last visited

  • Days Won

    1

  • Feedback

    100%

 Content Type 

Everything posted by blind_elk

  1. blind_elk
    Have you checked all the fuses? Also, check the fusible link which is attached to the +ve battery cable.
  2. blind_elk
    In the R32, difficult to start after warm up, ie when engine is hot, can be: Engine temp correction - check the engine temp sensor resistance value, and check the sensor output voltage. Fuel pressure - try disconnecting the vacuum hose from the FPR, or clamp the return line. Cranking speed - how good is the battery? Probably similar in the R33.
  3. blind_elk
    Has anyone noticed that the "time of post" is EST, rather than EDST? (this is actually being posted at 20:33 EDST)
  4. blind_elk
    CAS doesn't do anything to the timing (in terms of adv / ret). It simply lets the ECU know where TDC and each of the 360 crankshaft degrees are. It certainly fits and works on a RB20DET. Sorry, can't help you with the TPS.
  5. blind_elk
    When you own the car, you can run the hose wherever you like.
  6. blind_elk
    Then youneed to crack the union into the master (where the outlet pipe joins the master cylinder).
  7. blind_elk
    We've just been discussing it here: http://www.skylinesaustralia.com/forums/topic/351472-catch-can-install-is-this-the-right-way/ (Yes it's a 25, but the principle is the same) What you are proposing is illegal because it vents fumes to atmosphere. The alternate solution keeps the system sealed and recycles all gasses / fumes.
  8. blind_elk
    It's just the angle of view. If it were a problem, I would have done something different.
  9. blind_elk
    Have you bled the master cylinder? It should be bled first, then bleed the wheels (LR, RR, LF, RF)
  10. blind_elk
    No you don't! Here's mine, stil complying with the requirement to have a fully sealed system not venting to atmosphere:
  11. blind_elk
    Fred Gibson removed the HICAS from the race cars because it had the nasty habit of turning the car around if you backed off halfway around a corner. Not an ideal situation on the racetrack. NEVER believe the odometer of a car delivered from Japan.
  12. blind_elk
    Pretty sure that won't work. You still have it set up so that oil and oil vapour can be sucked into the intake side of the turbo, particularly under boost (high load) conditions. And that is exactly when you don't want it to happen. The PCV valve only opens under high vacuum (low load) and detonation from the oil vapour isn't a problem.
  13. blind_elk
    Push Button just above the main dial. (it's common problem, and there are many posts about it)
  14. blind_elk
    How old is the battery? Skylines aree notorious for being sensitive to voltages. Older batteries take more current to recharge after a cold start, and most of the ECUs view this as a problem, and misbehave accordingly.
  15. blind_elk
    The distributor should only install one way, because it is aligned by an offset tag on the distributor drive shaft.
  16. blind_elk
    Do you have same size tyre / rim combo on all 4 corners?And my money is on the throwout bearing (should have been replaced when the OS giken was installed).
  17. blind_elk
    I'm pretty sure the engine bay isn't anywhere long enough to accommodate 6 cylinders. A grunty little 4, along the lines of the CA18, is likely your best bet. But then you need to worry about how to make it stop. And turn corners. Maybe address those problems first.
  18. blind_elk
    Sounds like the solenoid on top of the starter motor has jammed. In "old school" fashion, use a bigger hammer and give it a jolt, see if that frees it up. But first, chek that the starter wire hasn't disconnected from the solenoid.
  19. blind_elk

    Spotted Thread

    blind_elk replied to paulr33's topic in Victoria

    Westgate Bridge (inbound) around 5pm today - "Black and White" R34, rego JDMCOP
  20. blind_elk
    Unless you fully understand the principle for the usse of a thermo fan, and know how to properly install it and properly operate it, stick with the factory setup. I'm sure Nissan knew what they were doing when they decided on the use of the viscous clutch type against a thermo setup.
  21. blind_elk
    Pretty certain the switch is in the same unit as the sender. Have you checked that the wires into the sender / switch are still intact?
  22. blind_elk
    Looking at the spec sheet for Toyo's Proxes 4 (most manufacturers would be similar), the recommended max width for a 245/45x18 is 9", and for a 225/45x18 8.5"
  23. blind_elk
    If you travel on the Indian Pacific, you can take your car for $849. http://www.gsr.com.au/site/indian_pacific/taking_your_car.jsp
  24. blind_elk
    I've found the tacho reads a bit higher than actual. The last time I bounced the limiter, tacho was showing around 8k.
  25. blind_elk
    No it won't! The ECU only runs for about 5 seconds when you turn the key to IGN, just to pressurise the fuel system. Back to OP, I had mine off the road for about 3 months, still ran fine when it finally got re-started.
×
×
  • Create New...