Jump to content
SAU Community

Recommended Posts

Hey guys

R32 GTST

Had to replace radiator.

I think I have an air lock

What is the correct way to bleed the system? I think I should have replaced the thermostat aswell, cause the bottom hose doesnt get hot even after a 40 minute drive (i.e. I don't think it's flowing)

All I have done is run the car till it was warm with the rad cap off. I also tried removing the bleed screw on the top of the engine/inlet. Am I supposed to do that hot or cold? While the car is running? When do I put the bolt back in?

Any other ideas? I assume the bottom hose should get hot? How can I tell if it is passing coolant through or not?

Also, where is the drain bolt on the head that I hear people talk about? I can't find it

cheers

Chris

Edited by eXc
Link to comment
https://www.sau.com.au/forums/topic/102301-bleeding-air-from-coolant/
Share on other sites

have you taken the top and bottom hose off the radiator and stick the hose in the top, then turn it on, to see if it flows?

Huh? Put the bottom hose onto the top of the engine? That would put water the wrong way around?

Can you explain in more detail?

heh... bottom would stay cold if your waterpump died, right?

No flow and no airbubbles when you leave the cap off... would explain that too.

I get air bubbles from the bleed point, and at the radiator cap...well...I did for a while until it put all the air out...

I still get air bubbles at the bleed point....but I don't know the right way to use it.

Water pump is only ~6000 kms old too

Edited by eXc

oh cool.

Black32 means:

1) Take out the radiator completely.

2) Stick the garden hose down the top

3) Watch the water flow out the bottom.

Pain in the ass, but if you really suspect a blocked radiator, this will tell you for sure. (and also give you a nice radiator flush)

oh cool.

Black32 means:

1) Take out the radiator completely.

2) Stick the garden hose down the top

3) Watch the water flow out the bottom.

Pain in the ass, but if you really suspect a blocked radiator, this will tell you for sure. (and also give you a nice radiator flush)

Ok. yeah I did that.

Can anyone tell me how to bleed the system correctly please?

I mean I have been running it for a few days with no dramas so I guess it's all good. But would be nice to check it out.

  • 1 year later...

I need help also!

I have an R32 GTST - RB20DET.

I filled it up with coolant, put the radiator cap back on and started the car.

I then fully removed the bleed bolt. I left it idling for around half an hour with heater on full (32'C FAN SPEED #4). I was told to wait until bubbles stop coming out and you just get coolant but it never happened. Got close a few times, but bubbles kept coming up now and again.

I should note that it wasn't a steady stream of bubbles/coolant coming out. It was very intermittent and sometimes you'd see the bubbles/coolant start coming up but then go back down. A lot of air bubbles came out but still never got just coolant to come out.

Radiator is full and overflow is above min.

What am I doing wrong?

I think you should run the car, then stop it and allow to cool down. open the radiator cap when cool and open the bleed bolt, i just keep adding coolant as it flows out of the bleed bolt until its a solid stream of coolant then put bolt back in and top raditor and put cap back on.

do you guys think my car will be safe to drive???

not much coolant was making its way out of the bleed valve, i would've lost a few mm of depth in radiator after 30mins, thats it.

how long should it take to get all the air out because i had it idling for at least 30mins slowly getting (some of) the air bubbles out but surely it doesn't take that long?

how do i make sure all of the air is out?

I had the same thing. The last time I did it I hardly bothered with the bleed bolt. Just idle it up to operating temp with the bleed bolt almost out and the rad cap open -keep topping up. Take the car for a short drive (with cap and bolt done up). Let it cool..open up bleed screw, then rad cap and add extra.

  • 1 year later...
  • 12 years later...

@cogsDo you happen to know exactly where the bleeder screw is? Having issues getting air out of the system on my rb20 and can't find any info on it. Replaced water pump and thermostat and deleted the heater core inside the car and i can't get the system to bleed properly. Trying to hit an event this weekend. 

  • 3 years later...
53 minutes ago, silviaz said:

I read on YouTube that the neo has 2 bleeder valves? Can't see anything in the manual though

Screenshot2025-01-23at8_48_41PM.thumb.png.7e03e5208b2ad237d7e74aa68cb7c641.png

IACV has an air bleed plug in this part of the engine manual. I'm guessing if it isn't bled it will cause weird idle behavior as the cold start valve won't get hot enough to close properly at the usual rate. 

  • Thanks 1
7 minutes ago, joshuaho96 said:

I'm guessing if it isn't bled it will cause weird idle behavior as the cold start valve won't get hot enough to close properly at the usual rate.

Not that anyone in most of Oz would notice if there wasn't coolant flow.

When I bought my Neo, that whole coolant path was completely blocked with solid crap. I had to dig it out so that I could bleed the cooling system properly, but until I did, I never struggled with idle control. We're not in Idaho.

1 hour ago, GTSBoy said:

Not that anyone in most of Oz would notice if there wasn't coolant flow.

When I bought my Neo, that whole coolant path was completely blocked with solid crap. I had to dig it out so that I could bleed the cooling system properly, but until I did, I never struggled with idle control. We're not in Idaho.

Kind of surprising, with cars this old I've seen a lot of them suffer from high idle due to internal vacuum leak. Fuel trims look fine but the cold start valve just wore out from all the heat cycles and won't close up all the way. Rather notorious issue in some models of the Toyota 4Runner: 

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah i found that alot of parts can be wrong or "very" hard to get the real right one. I already bought some brakes years ago on me "old" GT calipers and they were wrong too 😄  I told them too. Even send them pictures...but they said "EBC catalogue has them on my car... So i dont know what their answer will be. I call monday them and let them know that they are really not on my car. If they were they would be already on a car...
    • Welcome to Skyline ownership. Yes, it is entirely possible parts websites get things wrong. There's a whole world of inaccuracies out there when it comes to R34 stuff (and probably 33 and 32). Lots of things that are 'just bolt on, entirely interchangable' aren't. Even between S1 and S2 R34's. Yes they have a GTT item supposedly being 296mm. This is incorrect. I would call whoever you got them from and return them and let them know the GTT actually uses 310mm rotors. Depending on where you got them from your experience and success will obviously vary.
    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
×
×
  • Create New...