Jump to content
SAU Community

Recommended Posts

Just wondering if anybody has ever tried the spark plugs with dual electrodes (in the picture right) (do you have them in OZ at all?)

I use them in my motorcycle and it is definitely a huge improvement over the standard plugs.

Of course I don't know about the Skyline, but I will give it a try ..

Cheers from London :P

CLick here for the picture ...

dual - tri - quad spark they're all around on bigger machines. I just go with what works.

Hello there ...

BCPR6ES ->

BC = TREAD DIAMETER = 14mm

PR = PROTECTED INSULATOR + RESISTOR

6 = HEAT RANGE

E = THREAD LENGTH = 19mm

S = STANDARD SPARK PLUG TYPE

BKR6E-11 ->

BK = THREAD DIAMETER = 14mm

R = RESISTOR

6 = HEAT RANGE

E = THREAD LENGTH = 19mm

11 = SPARK GAP = 1.1mm

So the only difference between those 2 is that you have a protected insulator type (whatever this is?) and a standard gap as opposed to 1.1mm.

I hope this helps :mellow:

Cheers from London,

Andrew

the BK plug is shorter from the washer to the terminal (where the lead or coil clips on) than the BC plug by 2.5mm. so using the BC plug is going to make it sit up into the coilpacks a bit better and probably help with contact in the coils

the BK plug is shorter from the washer to the terminal (where the lead or coil clips on) than the BC plug by 2.5mm. so using the BC plug is going to make it sit up into the coilpacks a bit better and probably help with contact in the coils

Hi there ...

Thanks for the information .. I was already scratching my head why there is BC and BK when it's the same thread diameter anyway.

Cheers from London :iluvff:

Just wondering if anybody has ever tried the spark plugs with dual electrodes (in the picture right) (do you have them in OZ at all?)

I use them in my motorcycle and it is definitely a huge improvement over the standard plugs.

Of course I don't know about the Skyline, but I will give it a try ..

Cheers from London :iluvff:

CLick here for the picture ...

The number of ground electrode doesn't improve the intensity of the spark, it only serve to prolong plug life by distributing the spark erosion among the 2 electrode. The key to stronger spark are smaller centre electrode provided by iridium or platinum, the smaller the centre electrode the better.

Ignition sequence

Edited by Trex101
Just wondering if anybody has ever tried the spark plugs with dual electrodes (in the picture right) (do you have them in OZ at all?)

I use them in my motorcycle and it is definitely a huge improvement over the standard plugs.

Of course I don't know about the Skyline, but I will give it a try ..

Cheers from London :iluvff:

CLick here for the picture ...

To be honest the less plug in the chamber the better, extra electrodes offer more places for hot spots to form (early detonation) i find with super 4's and the multi lectrode plugs that as the engines heats up under race type conditions the amount of total timing the engine will take is BELOW that of single electrode plugs.

My pick for high horsepower engines (these make power :D ) are the fine NON projected plugs (see below) or for general performance simple BCPR7E

post-34927-1247727778_thumb.jpg

Edited by URAS
The number of ground electrode doesn't improve the intensity of the spark, it only serve to prolong plug life by distributing the spark erosion among the 2 electrode. The key to stronger spark are smaller centre electrode provided by iridium or platinum, the smaller the centre electrode the better.

Ignition sequence

Hi,

But doesn't the area where the ignition actually happens increase due to the 2 electrodes?

?

To be honest the less plug in the chamber the better, extra electrodes offer more places for hot spots to form (early detonation) i find with super 4's and the multi lectrode plugs that as the engines heats up under race type conditions the amount of total timing the engine will take is BELOW that of single electrode plugs.

My pick for high horsepower engines (these make power :iluvff: ) are the fine NON projected plugs (see below) or for general performance simple BCPR7E

Hmmm .. interesting!

What do you think causes the heatup?

As for 'the less plug, the better' I agree.

I don't know how the combustion chamber (in the head) looks like in a Skyline.

Does the plug sit in some kind of recess or is it just 'dangling' in the middle?

Cheers,

Andrew

it only earths to one, not all. Therefore your just shiilding the spark with the other earths.

Single is best!

But if you look at the picture you see that both electrodes are on earth.

(Or did I get you wrong?)

The spark should therefore distribute evenly between the 3 electrodes...

(at least that was my idea about the whole thing)

But if you look at the picture you see that both electrodes are on earth.

(Or did I get you wrong?)

The spark should therefore distribute evenly between the 3 electrodes...

(at least that was my idea about the whole thing)

Contrary to popular belief, multi-ground does not mean multi-spark. The spark will only jump once at a time to the lowest resistance ground.

Multi-Ground

Contrary to popular belief, multi-ground does not mean multi-spark. The spark will only jump once at a time to the lowest resistance ground.

Multi-Ground

Hmmm ...

Quite interesting ...

But I think that depending on the ignition system there actually could be two sparks forming.

If the ignition voltage/energy is not very high there will be just one spark developing, and it this makes perfectly sense...

However, if there is a very energetic ignition system present, it's a whole different story.

I will check in a lab test which way the sparks go. :P

Thanks for the link! :P

  • 1 month later...

are the regular NGK plugs copper?

i bought some BCPR6E-11 plugs today (these must be the V-power ones coz they got that grove in the electrode) just wondering if these ARE copper plugs as the guy behind the counter said they're just regular plugs. btw they cost $17 for 6

http://www.kaila.net/tl125/tl125ngkcode.html

BCPR6E & BCPR6ES are the same, its BCPR6EY which have the V in.

Normal spark plugs arent copper, they are nickel, but copper cored. If they were copper, there would be no market for iridiums (as copper is alot more conductive), copper itself couldnt handle the temp's in a combustion chamber.

  • 4 weeks later...

Ive just gone through reading the whole thread at the moment i have bcpre6e at 0.8 running 14 psi with spitfires no missing now im wanting to change plugs before my tune where the car will be running about 18-20psi and what ive gathered is to go with bcpr7e or bkr7e , will these plugs to the job? its for a r33 s2

bkr7es or bcpr7es. Get the std electrode, not the v groove as you can start to have spark break down at higher boost.

Can't say i've ever seen a v groove bcpr skit_31, though for the sake of argument you may want to look at the post above my previous one from a guy who has bought some and stated they have a V, and i have always bought bcpr6/7es's and they have always been standard electrode.

You can argue the vernacular on the copper vs nickel if you want, I'm not particularly fussed either way. When people say copper they are talking about regular old plugs

Edited by badhairdave

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...