Jump to content
SAU Community

Recommended Posts

See the below pic, anyone have these on their GTR - the bit from the front lower lip to the wheel well...

Are they are factory part, or are they a Nismo part??

I don't have em, and want a pair :D

Please enlighten me

I figured that you could duct them to the brakes...

cheerio :D

Untitled-1.jpg

I was actually looking at not having such a dramatic change in cross sectional area along the length of th educts...as i thought doing so may cause turbulence at the inlet and hurt flow...albeit it would increase the velocity of air...

No doubt Nissan no more then me. :) But looking at race cars, after having a large throat to capture air, they typically maintain a similar cross sectional area, even if they do go freom rectangular passage to 80mm flex duct.

My undertray also goes to just in front of the steering rack...if you want one should be a bolt on between GTST and GTR once i am sure the ducting works (LOL, bring on Sandown)

I have them on my GTR....well i have one now! The other one ripped off as i had to drive somewhere without a front bar (cooler hose blew off and i was already 1hr late). I dont think the cable ties held it well enough. I was thinking of going proper ducting like V8 supercar style instead of using these. Otherwise i gotta find one more!

My 89 has them.  Looking at FAST suggests they are standard part for JDM spec R32 GTR's

I should add that my car also has a curved rubber 'defelector' attached to each of the tension (castor) rods, which directs air from the ducts onto the back face of the brake disc through a hole in the backing plate. These also appear to be a standard JDM R32 GTR part.

I doubt that it's particularly effective, but better than nothing.

I was actually looking at not having such a dramatic change in cross sectional area along the length of th educts...as i thought doing so may cause turbulence at the inlet and hurt flow...albeit it would increase the velocity of air...

i think the intention here was to have them double as pie coolers. pie too hot? place in front of duct, drive for 2 minutes then remove. perfecto. the reduced cross sectional area stops said pie from entering brake rotor - messy.

Edited by Scooby

My R32 V-Spec II has them, but I have only kept to the tow point of the factory part, cut the rest off, installed a PCV downpipe section to convert the 4"x1.5" duct into a round 3.5" duct and run heat tollerent flexi ducting back to the rotor centre.

The item on my car that isn't in that pic is an extra air guide on the castor rods... again, cut and shut the air guide and its now just a bracket that the ducting is braced to.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
    • To drain the Intake Heat Exchanger, there is a crappy drain plug in front of the driver's side front tyre: You should use the largest headed phillips screwdriver you had, and in my case I needed vice grips on the hose above as the plug was tight (tighter than it needed to be, since it has an o-ring seal).  After you have a tray down and open the drain, open the intake heat exchanger reservoir cap (drivers side one) and you should get a couple of litres of coolant To get to the radiator, you need to remove the plastic engine undertray. It is held on with a series of 10mm headed bolts and some clips. For the radiator, there is another type of crappy drain (kind of like a plastic banjo bolt) and you should attach a length of hose to direct the stream of coolant per this pic (otherwise the coolant hits the rad support and goes everywhere). The drain is on the rear of the radiator on the driver's side and a bit hard to find. Put a big tray or bucket down (5l won't be enough) and slowly unscrew the fitting by hand. You only want to remove it far enough for coolant to flow, it you unscrew it right out the whole fitting and direction pipe will come off and you will get a coolant bath (yum!). Undo the radiator reservoir cap and it should empty about 8l
    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You also need to drain the intake heat exchanger to remove the radiator so you will need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. 2 other tools that really help dealing with coolant lines and spring clamps are Bent Needle Nose pliers Hose pliers Between them they will reduce the frustration (and injury) potential by about 1000% Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
×
×
  • Create New...