Jump to content
SAU Community

Recommended Posts

  • Replies 286
  • Created
  • Last Reply

Top Posters In This Topic

superb greg, so am i right in thinking if i buy this kit i can just bolt my rb26 4wd sump to my rb30 block?. nothing else needed?. except sump goo

p.s. greg pm me a price delivered to the uk please...

my uk postcode is pr73pd... asap.... :thumbsup:

superb greg, so am i right in thinking if i buy this kit i can just bolt my rb26 4wd sump to my rb30 block?. nothing else needed?. except sump goo

p.s. greg pm me a price delivered to the uk please...

my uk postcode is pr73pd... asap.... >_<

looks like proengines have these on ebay now. go to ebay.com.au and search for RB26 or RB26dett and you'll see it.

  • 3 weeks later...

Hi Guys,

Has anyone got any advice/pictures on how to do the fitting to the block for the rear Turbo Drain? Looking at it today its a bit of a pain. It it very close to a bolt which goes through the sump adaptor ans into the sump. This bolt has to be ground down on one side to get at the fitting properly.. On top of that, if the fitting protrudes too far its going to foul on the axle casting... (hope you are following me here...) :)

The front turbo I am draining to a dash 8 fitting on top of the wing of the sump.. so that's no prob..

Anyone got any info or pics of how they have done this with twin low mounts?

Cheers!

Hi Guys,

Has anyone got any advice/pictures on how to do the fitting to the block for the rear Turbo Drain? Looking at it today its a bit of a pain. It it very close to a bolt which goes through the sump adaptor ans into the sump. This bolt has to be ground down on one side to get at the fitting properly.. On top of that, if the fitting protrudes too far its going to foul on the axle casting... (hope you are following me here...) :)

The front turbo I am draining to a dash 8 fitting on top of the wing of the sump.. so that's no prob..

Anyone got any info or pics of how they have done this with twin low mounts?

Cheers!

for mine i just took out the std fitting in the block, went down to pirtek and got a t-piece. I then put that in the block and ran rubber hose from each drain to the t, easy! (hose has heat wrap on it too)

the motors in the car atm, but ill see if i can get some pics

for mine i just took out the std fitting in the block, went down to pirtek and got a t-piece. I then put that in the block and ran rubber hose from each drain to the t, easy! (hose has heat wrap on it too)

the motors in the car atm, but ill see if i can get some pics

Really?? I don't know how you got it in there... we (my mechanic and I) were looking at it and figure we have to get the bolt that holds the sump on in there first, and then you can 'turn' and right angle or t-piece as it will run into the edge of the sump etc.. but heh, obviously you've done it. If you can get a picture of it (although I imagine that would be a pain in the as$.) then I'd love to see it..

Have you run it yet Shane? I was going to run a t-piece but a few people have suggested running them separately "just in case"...

How do those N1's spool up!?

hi matt, like shane i have a t piece into the block. there is no way I could get mine off without moving the sump as it has a buffalo horn layout ie the ends on the t piece are quite long, and it would hit the driveshaft flange. it clears the block easily as it sits out a bit so we put the sump on after fitting the t piece. my t piece is fabricated from tubing, i did not use a pirtek piece as i'm not as flashy as shane :)

Edited by Scooby
Really?? I don't know how you got it in there... we (my mechanic and I) were looking at it and figure we have to get the bolt that holds the sump on in there first, and then you can 'turn' and right angle or t-piece as it will run into the edge of the sump etc.. but heh, obviously you've done it. If you can get a picture of it (although I imagine that would be a pain in the as$.) then I'd love to see it..

Have you run it yet Shane? I was going to run a t-piece but a few people have suggested running them separately "just in case"...

How do those N1's spool up!?

engine's only in for clearance purposes, dry sump/exhaust/bonnet. i've just got a new head so theres heaps of work still to do :thumbsup:

just took these 2 pics. thinking back now i did put the t-piece on b4 the sump, and looking at it now, i agree with scooby that theres no way u could get it on/off with the sump on lol

1001093xk4.th.jpg1001094vg9.th.jpg

hi matt, like shane i have a t piece into the block. there is no way I could get mine off without moving the sump as it has a buffalo horn layout ie the ends on the t piece are quite long, and it would hit the driveshaft flange. it clears the block easily as it sits out a bit so we put the sump on after fitting the t piece. my t piece is fabricated from tubing, i did not use a pirtek piece as i'm not as flashy as shane :)

come on scoobs, just call me a ricer :D

engine's only in for clearance purposes, dry sump/exhaust/bonnet. i've just got a new head so theres heaps of work still to do :bunny:

just took these 2 pics. thinking back now i did put the t-piece on b4 the sump, and looking at it now, i agree with scooby that theres no way u could get it on/off with the sump on lol

1001093xk4.th.jpg1001094vg9.th.jpg

come on scoobs, just call me a ricer :D

Haha! Thanks guys. hmm.. you've thrown an extra variable in there now Scooby... I not only have to come up with a solution, but it has to be flashier than ShaneF's!!! :thumbsup:

Cheers for the feedback (and photo especially) - at least it confirmed that the sump had to be off to get the fitting in there... was wondering if there was a secret fitting I didn't know about that was perfect for the job.

I was thinking of taking the existing plug, welding a dash 8 fitting to it and then drilling it through the centre, that way I'd probably be able to fit and remove it with sump on. But once its in there - I doubt I'll really ever need to take it off anyway.. so off I go to Pirtek I think!

Cheers guys!

hmm actually having another look at the photo, your block looks a little different to mine Shane.. Series 1 and 2 perhaps? (I don't know the differences)

Mine has fittings just next to the drain where I need to put a bolt through. And this is the other prob I have, the bolt can't be turned and tightened up with the fitting in place! The head of the bolt has to be ground off - and then the fitting put it... which of course means the sump must already be on...

Excuse the phone photo - but this might show what I am talking about..

(upside down Miss Jane)

post-20408-1180943548_thumb.jpg

No idea what them 2 nuts are for mate :thumbsup:

Side note: The hose you'll need for the turbo drain will have to be VERY flexible, ull also need some heatshield stuff caus it comes awefully close to the dumps :bunny:

  • 4 weeks later...
  • 4 weeks later...

just an update guys.just fitted my proengines sump adapter. what a fooking top notch bit of kit. superb, every hole lined up a little grinding a per instructions which i have to say are also fooking brilliant. you need one buy this kit..END OF SIMPLE..bernie uk..

  • 2 months later...
  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...