Jump to content
SAU Community

Recommended Posts

For some of the people in this post who didn't get what I was saying-

- it's not a fault. all buses do it of certain make(s) do it.

- i didn't say it was necessarily a bov used for turbos. it is air escaping so it's "blowing off" in some form or another. personally i think it's the door/brake pneumatics.

- it hurt my ear and I want to sue the government (not serious) so what would i do? why isn't this noise pollution? (does anyone know if it's just accepted or 'enshrined' in law somewhere?)

Thanks :(

... ps.

Can anyone tell me where to get one of these bus BOV's? and is there an adaptor to fit them to my laser turbo?

SIK WLEH BROTEC comes to the rescue.. PM me for a good price.

You sure thats an exhaust brake?

Not saying your wrong but I drive trucks and have not seen one set up like that before. I have only ever seen the butterfly flap in the exhaust pipe and the Jake brakes which hold the valves shut for the engine braking. How does that one work.

In relation to to BOV noise, as mentioned its the pneumatic release from the air brakes and in a bus situation from the airbag suspension as well. Sometimes when there stopped on a slope you see a bus rocking forward and backwards as the airbags try to level themselves.

I look at the engine setups on our trucks all the time and I have no friggin idea whats going on. One engine has an internal wastegate along with an external gate as well that seems to vent back to the inlet manifold?

And on the inlet piping they have multiple pressure actuators that I have not a clue what they do, when they open/close and what for.

couldnt they suppress it something? it shouldnt need to be that loud...

it real bad in a loading bay, the truck reverses in and the brakes squeels a little before it stops, then PPPPSSSSSSHHHHH!!!!! and you nugget your pants :/

Yep, that's an exhaust brake. A Jake brake uses oil pressure to the hydraulic lash adjusters which cracks the exhaust valve on the compression stroke preventing the compression ignition combustion (no spark plugs) from completing so it "brakes" the engine.

Don't be afraid big rig and bus noobs, the noises won't hurt you. :P

Its can also be height adjustment

Thats air driven aswell (esentially air bags i think).

SOme super new buses can change ride height depending on passenger load.

They too can be noisy. Not as loud as the compressor veniting though

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
×
×
  • Create New...