Jump to content
SAU Community

Recommended Posts

I've just redone my light/moderate load ign. and afr's...

Should be interesting next tank, the ignition has actually made quite a difference to how the car feels off idle, prior accelerating from a standing start in second would have it bog for a fraction of a second, now it simply accelerates without bogging. :D

I've got a real strange issue around 2000rpm as the turbo tries to make more than a few psi, it appears to bog, boost goes up, afr reading goes way lean then as soon as it gets over 2000rpm it clears its throat and acceleartion literally snaps on.

I'm assuming this may have some thing to do with the n/a cams running around 8degree's overlap and such a small turbo.

Nothing I do will get rid of it, super rich afr's, lots or little ignition timing or a mixture... Buggers me.

  • Replies 58
  • Created
  • Last Reply

Top Posters In This Topic

Question... i have rb20 wit z32 afm/gtr injectors and im gettin 300ish kms to a tank, i had standard injectors and afm and got around the same, isn't that abit sh*t for an rb20?? I would like some fuel economy but if i cant have some decent hp and economy, well i did buy a car with a turbo n id understand lol Ive just seen some figures off rb20s and even rb25s that blow me away, even with i baby the motor!

Edited by jazza08

Its all about maintaince, I'd also have to say (in my case) it doesn't have so much to do with tuning as on the base pfc maps with z32 and gtr injectors & the 3ltr I was pushing 440km's per tank.

The only time i've dropped to such fuel economy levels is when my injectors were shagged, the o2 sensor was still ok but definitely a tad slower than the new genuine o2 sensor I replaced it with.

So as I believe I've said before...

Check for vacuum leaks, ensure o2 sensor and injectors are in good condition and motor in good condition.

And drive sensibly, short shift around 2500rpm and use a little more throttle to get the car moving, driving like this its also critical your tuner doesn't have the afr's dropping to flat 12's as soon as any boost is made.

From factory my rb20det driving as such would hang in closed loop until roughly 2psi was being made, so it was running lean, possibly why it consistently returned just under 500km's to a tank.

But as with everything there are bad cars and good ones... Its just finding what is causing the problem. R33's suffer the poor fuel economy problems much more often than the R32's, its not displacement as I've noticed no real noticable difference and i'm 1ltr over a 2ltr. :)

  • 7 years later...

Most of you guys are getting good economy! My 25/30 is running 19/100km no matter how I drive.

That's on a 25 tune @5psi. On the wideband it shows 14.5-15.8 in closed loop but gets right up to 11.1 at wot.

Will hopefully get better when I get my pfc and sard 800cc fitted and tuned.

I think the roads to good economy are CR injectors and gearing . An RB30 with at LEAST 9.5 static CR should make real good part throttle torque . I also think good injectors like EV14s help heaps because they have fine control (if tuned properly) at short pulse widths .

Most R series Skylines were geared to suit the std RB20/25/26 and Japanese roads , depending on the lump you removed the gearing can be pretty short for a 3 litre . I don't think any turbo R series was taller diff wise than 4.1 and a 3.9 would allow you to better use the extra part throttle torque . Note the difference in rear gearing between some JDM and some Aus spec S series cars , 4.1 to 3.7 in one case from memory .

Lastly and very importantly , turbine back pressure . If the turbine/housing combination is small this hurts consumption too .

A .

I think the roads to good economy are CR injectors and gearing . An RB30 with at LEAST 9.5 static CR should make real good part throttle torque . I also think good injectors like EV14s help heaps because they have fine control (if tuned properly) at short pulse widths .

Most R series Skylines were geared to suit the std RB20/25/26 and Japanese roads , depending on the lump you removed the gearing can be pretty short for a 3 litre . I don't think any turbo R series was taller diff wise than 4.1 and a 3.9 would allow you to better use the extra part throttle torque . Note the difference in rear gearing between some JDM and some Aus spec S series cars , 4.1 to 3.7 in one case from memory .

Lastly and very importantly , turbine back pressure . If the turbine/housing combination is small this hurts consumption too .

A .

That's why I am still looking for an R34 GTR non v spec diff (3.545) not just for the fuel economy but more for more restful cruising at 110km/hr

Nick, isn't your in a patrol? The extra weight would make a huge difference.

I am getting just over 13 driving to and from work mostly (12ks each way) with my auto rwd Stagea. I have been meaning for ages to tweak all of the cruise section of my tune but still haven't.

800s because they come up cheap, New still sealed in box's for $200.

If something better Sized shows up for sale I'll get them, I really only wanted bigger than stock- like 400-500cc

Yeah it's in a patrol, on 35s and 6in lift so she's pretty aerodynamic!

And it has 4.94 diffs.

It does 2550rpm at 100km.

And it weighs 2200kg, probably bit more with a full tank.

Edited by nicksamaniac

Why are you getting Sard 800 injectors? They won't help your economy. Are you going for 500KW?

500Kw at least!

I want to be able to lift a wheel whilst overtaking at 100km/hr!

But more seriously I was just gonna put it on the Dyno and lean on it (to a safe enough level) and see what it makes.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
×
×
  • Create New...