Jump to content
SAU Community

Recommended Posts

Daily! I had two cars before the other one being a 1.6 pulsar great on fuel. But everytime i drove that i got bored and annoyed and wanted to be in the r32 so i sold the pulsar so i could at more mods to the 32

Edited by polak_32
  • Replies 90
  • Created
  • Last Reply

Top Posters In This Topic

daily driven 40 each way to and from work and and any other running we do its nearly always in the line .. why bother having a piece of motoring history to have it hidden away in a garage nearly all the time... its more econimical than my commonwhore was

I don't have a Skyline, but I have a 180sx, which is probably driven 2 to 3 times a month. I is more of a fun car and not really practical nor safe on the road. We got a daily to get to and from work. If I had a R33 or R34, I wold probably drive it more often. The build quality of Skylines are alot better. Another thing I have found is that because I don't drive the 180 around very often, I tend to enjoy the drive more in what would otherwise be a very uncomfortable car, especially on rough Aussie roads.

Jon

i just use mine on weekends mainly.. the trade off is getting to ride on the trains on weekdays..... :D can i just ask... how bloody hard is it for people to put deodorant on in the mornings ?? i dunno bout other states but in vic the trains are a cespool of disease

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
    • 440s will support well over 400HP on petrol, which is a decent place to be for an RB20. 230+rwkW. Will be a safer bet for idle/low load. 550s would be nice for the extra headroom. I've made the same decision with mine (Neo25). 1000s are probably too big for the Nistuned ECU, so I have some smaller ones.
    • Appreciate everything guys. I did go ahead and get an alignment... most of my complains are solved. Car is not perfect, but it's good enough. If I notice uneven tire wear or anything I'll just take everything back to stock.  Thanks again!
    • They still have not shipped the 550cc injectors as they weren't in stock, so in theory I could ask to get the 440cc ones instead, if those work better in my scenario. They're the same price so really shouldn't be an issue. Unfortunately I am not so knowledgeable in most parts of tuning so I wasn't sure what's best to choose between the two. 440cc ones are the lowest they have (not in stock, but available to buy nonetheless).
×
×
  • Create New...