Jump to content
SAU Community

Recommended Posts

Any graph to view? The outright power figure is very impressive for the boost you've run.

How are you finding the 56T / VG30 combination in terms of streetability and response with the 2.4 litre capacity?

  • Replies 121
  • Created
  • Last Reply

Top Posters In This Topic

i will get a graph once i get the tune checked over, i havent got one printed since the headgasket was changed. but had a quick look at the run he did and it had 12psi by ~100kph in 4th.

actually it feels really good, mind you i havent really tested it properly as i'm abit unsure how healthy the tune is, but the rb25 housing felt better in regards to response but had surging and boost spiking issues.

but SR20s spool turbos better than rb20s due to their longer stroke

what is the compressor and turbine A/R on the hks GTRS?

currently im really keen on the GT2871R highflow cos it all bolts up, and from what i hear, the exhaust A/R is 0.63

HKS unit has comp .60A/R, turbine .63A/R.

A carefully thought out high flow can work very well, but the apparent aims of factory engineering needs to be factored in when using factory-spec housings.

In some respects I'm not massively surprised that kwazza11 had troubles with surge with the 56T comp and 2.4 litre capacity. My calcs for the RB25 suggested it would be borderline, depending on the power target. Using the VG30 turbine housing is a way of masking a technical mismatch and still getting a satisfactory overall performance characteristic. If the compressor is not excited as easily due to the higher flowing turbine, then it will not be pumping as much air at the middling engine revs, giving a marginally lazier transient response but eliminating surge - and also giving excellent high end power. I actually think it was a clever and practical way of making the turbo mate well - just not how I would have/did do it.

If you are insistent on doing a Garrett GT2871R cartridge type high flow into RB20, depending on your exact objective then go either 48 or 52T comp, and use the RB20/25 turbine housing. If you can get some piping mods sorted, use the Garrett 0.60 A/R comp housing and have something close to a GT-RS. Just remember the more fabricating you have to do, then the financial advantages of going with this decision start to diminish.

cheers

Edited by Dale FZ1

Not really on topic but dale fz1 you sound like you know a fair bit about turbos, can you recommend any good reading, books articles etc for learning about flow maps, how to match compressors to a/rs to motors etc?

i agree dale, the 56t matched to the rb20/25 housing is definately on the edge. would be even worse on the stock bottom end, i actually order the 52t 2871r in the first place but the workshop i purchased it from sold me a 56t telling me it was the 52t, when i questioned him about it he said he hadnt realised and offered to chase up the proper comp but called me back 2 days later saying it would take him 2-3 weeks to get the wheel in. was sick of his BS by then so i ended up just keeping the 56t.

the turbo works really well, just make sure you have the wastegate bored out as much as possible if using any of the nissan housings.

Not really on topic but can you recommend any good reading, books articles etc for learning about flow maps, how to match compressors to a/rs to motors etc?

We'll stick on-topic here, but try

www.turbobygarrett.com and read their tutorials; they are very, very good and easy to follow

Turbochargers by Hugh MacInnes (if you can find a copy, will be in specialist bookshops).

I have another text that was published early 90s and still on loan to my mate.

cheers

its internal gated

have always had boost issues, previously, boost always dropped off, now spikes. Changed controllers no diff.

Its all good though, car doesnt ping and knock levels do not go over 20

h.

That you have knock apparently well controlled is a good thing.

I wouldn't be at all happy with the boost skyrocketing at the top end of the rpm range - recipe for a hand grenade under the right (read: wrong) conditions.

So your 2871R is fitted to an SR20, uses a .63 A/R turbine housing? It's a stock, off-the-shelf Garrett unit fitted to a fairly stock engine and manifolds?

What was changed that you went from boost falling away to boost running away?

Main point of interest is if there are any lessons to learn in fitting a similar spec unit to an RB20.

cheers

Hi boost at top end is not an issue, as i dont take it past 7000rpm. As you can see from the dyno. Hi boost is an issue down low, as thats when rods can break. Up top you'l only damage rings (so i have been told).

There 2 things that we are assuming which is the problem to why boost sky rockets

1. I have re-ground exh cam with ajd cam gear - that may need adjusting. Have set it to 0 and just fitted cam. If i play with the timing it may stop the boost spike and give me a fatter mid range.

2. Wastegate hole needs to be machined

I wont be doing anything for now as im happy.

If you are insistent on doing a Garrett GT2871R cartridge type high flow into RB20, depending on your exact objective then go either 48 or 52T comp, and use the RB20/25 turbine housing. If you can get some piping mods sorted, use the Garrett 0.60 A/R comp housing and have something close to a GT-RS. Just remember the more fabricating you have to do, then the financial advantages of going with this decision start to diminish.

cheers

i agree with Dale in that the ideal combo for a RB20DET would be a 48T GT2871R with a RB25 exhaust housing. this would allow the turbo to easily mate with the standard manifold and dump pipe if required.

the 56T comp wheel is just too big for the 76T turbine where it is able to flow enough air for ~475hp, whereas the 76T's efficient limit seems to be ~400hp. Also, i believe the 52T is probably as big as you'd like to go on the GT2871R although be it with an A/R .86 exhuast housing for ease of flow and increased efficiency.

if you look at the garrett website (www.turbobygarrett.com), you will see that the efficiency of the 76T turbine actually decreases as you go bigger in compressor wheel.

anyway, just my 2c, feel free to put me in my place if you feel you need to :)

  • 1 month later...

I have just purchased a HKS GT2530 upgrade kit from nengun Japan for my R32-RB20DET as my stock turbo shredded all the turbine blades like potato chips last week. I have been doing tons of research into which is the best and most practical turbo upgrade for the RB20 with T3 flange and I have decided to go with the 2530.

I have a long way to go and alot of mods to complete the project. I will keep you updated on how the installation goes and on final dyno results.

There are so many paths to take when upgrading the RB20 turbo. I hope my experience will help some of you to make the choice that is right for you.

Rgds, Grippy :P

I have just purchased a HKS GT2530 upgrade kit from nengun Japan for my R32-RB20DET as my stock turbo shredded all the turbine blades like potato chips last week. I have been doing tons of research into which is the best and most practical turbo upgrade for the RB20 with T3 flange and I have decided to go with the 2530.

I have a long way to go and alot of mods to complete the project. I will keep you updated on how the installation goes and on final dyno results.

There are so many paths to take when upgrading the RB20 turbo. I hope my experience will help some of you to make the choice that is right for you.

Rgds, Grippy :laugh:

Yeah well I'm in the same boat too but I ordered the HKS GTRS. It should be here sometime this week from nengun. Could be a few weeks yet till I can install it but it should be a well worth the wait.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...