Jump to content
SAU Community

Recommended Posts

Hay guys now i have serched all the threads and have been reading for a while now and nothing has realy court my eye on how to solve my problem.

This might have been covered and might be a easy fix but i would not know it

Im getting very tyred of changing tyres cos the first two inches of the inside tyres are bald and no where any where else.

From what i know i have stock everything down there in that area (breaks, the lot) but my car sits much lower then most other peoples.

the springs say Nissan and so do the shocks and have been told they are not cut but i only get this wear on the tyre now im pushing more power through the wheels.

Any help would be great.

Do i just need castor kit or something like that?

by the ways its only the back two tyres

Link to comment
https://www.sau.com.au/forums/topic/128695-guys-help-me-out/
Share on other sites

who can i get this from and how much

SydneyKid sells this in his group buy, check the group buys section

or greg from GKTech (EXAUNV on sau) sells whiteline products as well

if you check the whiteline website, and just pm him the part number he'll give you a price

centreline suspension should be able to supply them as well

i've always gotten cheaper prices from centreline than directly from whiteline.. don't know if it's cheaper than the other guys or not.

anyway if you give chris at centreline a call i'm sure he'll be able to give you some advice.

Actually you reminded me I really need to call him too :blush:

he has hammer toe... you can get plastic sleeves to help with that.... i seen em in one of those home ideas catalogues

I didn't think cars could get this . I 've heard ladies get camel toe ...but hammer toe? :happy:

Time to look at reco'ing your suspension buddy. After 12yrs+, bushes, shocks, springs, etc all go up the shit. I would seriously consider the full whiteline handling pack, with additional camber bushes and pinapples. As well as getting some new coil-overs.

All this will make your car ALOT safer and handle alot smoother. You have ample power, now it is time to support it :happy:

whats his number kas

I have a Centreline Suspension card in front of me...PHONE : 03 9469 2914 talk to Chris - he is the man when it comes to this stuff

I'm going down there next week for a camber kit also.

Edited by khunjeng
I have a Centreline Suspension card in front of me...PHONE : 03 9469 2914 talk to Chris - he is the man when it comes to this stuff

I'm going down there next week for a camber kit also.

yup, Chris at centreline certainly knows his stuff, he's not a bad racer either :happy:

There is a place in Baysie thats a lot closer to ya Scott if you dont wanna travel out to Thomastown

I think the name of the place is TechSport or similar.

If you get the kit from the groupbuy and take it there, you shouldnt have an issue.

If i recall the do a massive amount of road/rally EVO's and that sorta thing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...