Jump to content
SAU Community

R34 Gtt Boost Gauge

nuffsaid

By nuffsaid,
in Engines & Forced Induction

 Share

Recommended Posts

nuffsaid Veteran

nuffsaid

Posted
  • Author
Posted

Darn it aye, was hoping I wouldnt need to get a boost gauge

I thought they were either all inaccurate past the standard boost levels, or they were pretty much spot on.

I believe they are electrical gauges. Alot of the top brands sell electrical ones too, does this mean that they are also relateively inaccurate? Perhaps the boost sensor on the R34's isnt as good quality.

xRHETTx Mentor

xRHETTx

Posted
Posted

There is no real reason why the stock boost guages would be highly innaccurate, unless the sender has failed?

IMHO usually people go for aftermarket boost guages (and oil pressure and water temp) as they have more increments and are easier to read. With only 4 increments or so on the stock one its quite hard to read accurately. The difference between 12psi and 14psi is hard to judge for example, and one is safe and the other is possibly not.

32GTRB Proficient

32GTRB

Posted
Posted

ive got autometer cobalts on mine (boost/vac on an xr6 turbo). my gauge is pretty accurate when there is constant acceleration (auto, gauge is mechanical), however when i floor it and it kicks down a gear, it spikes up to 10psi, and then returns to 6psi.

my gauge also lags abit because i have kinks in the nylon tubing, which i will be replacing soon.

benl1981 Grand Master

benl1981

Posted
Posted

Its good to have a nother gauge but not really needed.

In my R33 I occassionally use an old pressure gauge I have that is fairly accurate to check the boost and see where it sits on the factory gauge.

I dont leave this connected and just have a glance at the stock gauge to see eveything is ok.

Stock gauges (iff same as R33) are a pressure transducer that sends a 0-4.5v (I think) signal to the dash.

I took a multimeter to it once but can't remmber the vs at atmospheric pressure (May have been 1.25 or 2.25v)

So it would be a 2bar MAP sensor...

0-1bar is vacuum

1-2 bar boost - due to turbo

+1 on the gauge would be about 14psi-15psi

xRHETTx Mentor

xRHETTx

Posted
Posted

Yeah Ive got a pivot stepping motor boost guage on my r32, it seems the stock one is pretty close.

With just a cat back and filter its running 0.7-0.75bar which is 10-11psi i guess.

The conversion from 100mmHg (what the factory guage is in) to psi is times by 1.934. So +7 on the factory guage is 13.5psi.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      I forgot about my shiny new plates!
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...