Jump to content
SAU Community

Recommended Posts

Nengun site so I'm not sure who/what translated it. Would be good to get a hold of some complete info. I had a look around for V specific info the other day to see if this was a feature on all F-CON models but didn't turn up anything.

its always goign to take a second or so to change gears on full throttle changes.. that's the way the nissan gearbox is

if you want to change that, then a shift kit is a great investment :)

If your are interested here is a xls file of raw data and graphs from Newkleers LCD Box and NissanDataScan software that I did the other day trying to sort out some problems.

It shows the timing cut and change from first to second at near 7000RPM.

The Auto has been modded with a firmer shift plate and Kevlar clutches, 2800RPM stall etc.

BTW this is with ECU ERROR 34 - Knock Sensor showing all the time.

Can anyone tell me the implications of this error on the ECU maps and general operation of the engine under this fault condition?

BTW this is with ECU ERROR 34 - Knock Sensor showing all the time.

Can anyone tell me the implications of this error on the ECU maps and general operation of the engine under this fault condition?

Sorry I cant give you a definite answer on this, but logic would say that:

Knock sensor not working = ECU assumes engine knocking (just to be safe and avoid a waranty claim)

therefore retard some timing.

HOWEVER - if you have set the timing when this was faulty you may have already compensated for the retard, but removed the safety measure on the rare occasion you get bad fuel or heat soak in the intercooler.

Well I have bought most of the parts and have gone with a PFC. I would have gone with an F-CON but no one in Vic tunes them. So I should have all the parts within a week or two but might wait til Jan to do the install. Depends on when I have a bit more cash to get the spare turbo rebuilt and pay for some of the install and tune. I'll be installing as much of it myself as possible but lets face it, I'm an IT tech not a mechanic. I can do a service, change plugs and coils but fuel pump and injectors and I have visions of exploding cars.

*edit...is there a seperate ecu for the auto transmission? or is it all inside the engine ecu?(front left of passenger seat)

for r32gts-t's

not sure on the 32's but the 33 has a seperate ecu in the right kick panel for thr auto.

  • 1 month later...
Glad I found this thread... I will add my Datsun 120Y that has a RB20DET auto

Engine has

20thou forgies

Walbro + Bosch 044 & surge tank

GTR ingectors

Stock AFM just before the throttle body

3" exhaust

Garrett GT35R 0.63 exhaust

38mm Turbonetics external gate

Auto has

MV shift kit

MV manual shift controller

B&M pro ratchet shifter

4200 stall converter

trans cooler

185 kw

I could only find my 13.1 @ 113 timeslip from yesterday but it has done a 12.9 @ 113.

Best 60 foot is a 2.25

I use 205x50x16 Toyo R1-R and a 3.7 lsd diff.

I have been told I have the incorrect type of muffler fitted and i need a straight through design.... Damn restrictive V8 muffs.

post-24062-1162824263.jpg post-24062-1162824293.jpg post-24062-1162824441.jpg

Well after finally getting a half decent converter in, last night i did a 11.89 @ 112mph.... 1.71 60 foot time.

I will upload the time slip in the next couple of days :)

Here is a pic ..

post-24062-1168510492.jpg

Update, the new fuel system netted a massive 157rwkw!

We lost AFR readings at 5000rpm...they dropped off way past 10:1

The new turbo/bleed valve combo won't hold boost either, this should all be fixed in the next 2 weeks with some nice figures to attach :wave:

  • 3 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
×
×
  • Create New...