Jump to content
SAU Community

Possible Job Availability

Bass Junky

By Bass Junky,
in Victoria

 Share

Recommended Posts

Bass Junky Grand Master

Bass Junky

Posted
Posted

Hey ppls.

The new place that I'm working may or may not require the services of a person detailed below.

We are a New and Used machinery dealer in Dandenong.

We buy machines both locally (used) and internationally (new).

We install and commission most machines ourselves.

We recondition machines that we have traded on new machines.

Job Description:

Cleaning of transport gunk (protectant oils and greases) from new machines

Cleaning down traded machines ready for work

Moving machines (up to 20 tonne) around a factory with one or two cranes

Moving machines (up to 1.5 tonne) around a factory with a forklift

General factory work to keep factory looking good

Spray paint machines

Depending on level of aptitude, installation and service work will also come.

Must be able to work for me :S

Must have some mechanical aptitude, ie know how to work a screw driver, spanner, grease gun, spray gun etc.

Must be able to start at 8 and finish at 4:30, 5 days a week with possibility of Saturdays sometimes if work requires.

All equipment provided.

At the moment I am just putting out feelers for this position and at the start it may be casual until we determine the amount of time it takes to perform some of the tasks required.

any questions, just ask.

BASS OUT

Link to comment
https://www.sau.com.au/forums/topic/134255-possible-job-availability/
Share on other sites
Bass Junky Grand Master

Bass Junky

Posted
  • Author
Posted

Adam, you are a funny man. But not Ha Ha funny :)

It would be much better if the person had a crane and fork license, but we could arrange training and licenses for said person if required.

West Grand Master

West

Posted
Posted
Hey ppls.

The new place that I'm working may or may not require the services of a person detailed below.

We are a New and Used machinery dealer in Dandenong.

We buy machines both locally (used) and internationally (new).

We install and commission most machines ourselves.

We recondition machines that we have traded on new machines.

Job Description:

Cleaning of transport gunk (protectant oils and greases) from new machines

Cleaning down traded machines ready for work

Moving machines (up to 20 tonne) around a factory with one or two cranes

Moving machines (up to 1.5 tonne) around a factory with a forklift

General factory work to keep factory looking good

Spray paint machines

Depending on level of aptitude, installation and service work will also come.

Must be able to work for me :S

Must have some mechanical aptitude, ie know how to work a screw driver, spanner, grease gun, spray gun etc.

Must be able to start at 8 and finish at 4:30, 5 days a week with possibility of Saturdays sometimes if work requires.

All equipment provided.

At the moment I am just putting out feelers for this position and at the start it may be casual until we determine the amount of time it takes to perform some of the tasks required.

any questions, just ask.

BASS OUT

Mav, go for it.

Bass forgot or he intentionally did not mention that its not only the machinery get move around but Bass every now and then move his boss R34 N1 GTR around the parking lot too :woot: .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Ball bearing turbos

      By GTSBoy · Posted

      The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • sunsetR33
      Ball bearing turbos

      By sunsetR33 · Posted

      Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • GTSBoy
      R33 GTST Axles

      By GTSBoy · Posted

      There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • jdniss
      Forced Performance Hta Turbos

      By jdniss · Posted

      Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • thozza
      Intro/R33 owner

      By thozza · Posted

      Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...