Jump to content
SAU Community

Big Up For A & B Motorsport In Brookvale !

B-Man

By B-Man,
in New South Wales

 Share

Recommended Posts

B-Man Grand Master

B-Man

Posted
Posted

As you may know - I have my fair share if 'interesting' experiences with mechanics & workshops. So when I go to one that give me outstanding service and quality of product (and price) - I like to share the goodness !

So the story goes:

Went looking for some coilovers for my TX3 race car project. A member of TeamEunos (like SAU but for Mazda/Eunos/Cosmo etc) recomended that I try A&B Motorsport in Brookvale.

Talked to Frank, the owner, and he showed my his inverted race coilovers with adjustable everything (damper, height, camber, etc) - they were a good price, so I told him that I'd think about it !

Whilst there - I noticed some 8 piston calipers with massive rotors and I asked him about them for the Cosmo - Although they didn't have a specific kit for the Cosmo - he said he could make one up for me. He also told me that I I took the coil overs, that he would fit the brakes for a good price.

So I went with the deal. He spent 2 days getting the brakes 200% right ! Didn't charge me for the 2 days and he had to make new brackets, and spend a bunch of time with different types of rotors to get the right offset etc.

As an example - the original wheel studs with the new rotors meant that the wheel nuts would only go on 80% - Most other workshop would have just left it at that - But being particular about his work, he hunted down 10 new studs that were 10mm longer that the originals - so that the wheel nuts went on fully and then some !

Very happy with the final result ! 8 Piston calipers, braided lines, all fluid changed, 330mm slotted rotors - It stops like a demon now !

I liked the coilovers for the TX3 - and asked about the Cosmo - again, no specific kit - but he would make one up - Sure enough - Got the car back - and perfect ! Sits lower - he got all the adjustments/allignment and stuff spot on 300% perfect. Ride is firm but comfortable and the car looks a hell of a lot better sitting lower and with the big brakes on the front !

So a big UP to Frank and Rob at A&B Motorsport in Brookvale !

Give them a hoy - if you are after brakes, suspension, etc - They also have a dyno - they don't tune yet - just power runs.

Cheers,

B-Man Grand Master

B-Man

Posted
  • Author
Posted

Suprisingly not !

My old rotors were warped - and the Cosmo come with tiny rotors and single pot calipers. So I investigated options - The best and most affordable option was 2nd hand FD RX7 Calipers with RX8 rotors. I figured about $2000-$2500 for this - Also there was a bit of machining and mucking around for this conversion.

Both Calipers, 330mm rotors, braided lines, fluid and pads, including fitting cost me $2,500.

Before the upgrade - front to left difference in pressure was 9% - Now it is less then 1%.

The brake kit is designed in Japan and manufatured in Taiwan - Brand is K-Sport ! (Similar to the ones Just Jap sells) but these guys are a workshop so any non standard stuff or hard to replace items (eg for a Cosmo) - they work out how to do it !

Very Happy !

Blitz Grand Master

Blitz

Posted
Posted
Suprisingly not !

My old rotors were warped - and the Cosmo come with tiny rotors and single pot calipers. So I investigated options - The best and most affordable option was 2nd hand FD RX7 Calipers with RX8 rotors. I figured about $2000-$2500 for this - Also there was a bit of machining and mucking around for this conversion.

Both Calipers, 330mm rotors, braided lines, fluid and pads, including fitting cost me $2,500.

Before the upgrade - front to left difference in pressure was 9% - Now it is less then 1%.

The brake kit is designed in Japan and manufatured in Taiwan - Brand is K-Sport ! (Similar to the ones Just Jap sells) but these guys are a workshop so any non standard stuff or hard to replace items (eg for a Cosmo) - they work out how to do it !

Very Happy !

Sounds good B-Man.

K Sport are exactly the same as G4 Racing (only the G4 kit is a little cheaper)

All the reports I have heard about G4 have been outstanding in terms of braking performance, particularly on the track! :)

rukus Grand Master

rukus

Posted
Posted
Sounds good B-Man.

K Sport are exactly the same as G4 Racing (only the G4 kit is a little cheaper)

All the reports I have heard about G4 have been outstanding in terms of braking performance, particularly on the track! :)

really?

nice... i need new brakes and was wondering what G4 were like..

B-Man Grand Master

B-Man

Posted
  • Author
Posted

Yeah - they are the same as G4 - However, in my case - if I had bought the kit from JJ, then got an adaptor made, new studs and all the labour - I reckon I ended up paying heaps heaps less !

They are awsome brakes ! absolutely briliant compated to the standard cosmo - there is no comparison !

T04GTR Grand Master

T04GTR

Posted
Posted

yep they are pretty cool. i bought som lk-sport coil overs and mucked around with springrates and they were fine with it. also both my rear dampers exploded(pulled the seel in and leaked everywhere) they replaced them no questions asked :P still in warenty but yeah .

i had to turn down the funny spaarkplugs and wierd vortex intake lol

Beer Baron Grand Master

Beer Baron

Posted
Posted

good man. especially if he had press studs on the back of those jeans. i'd he-bitch man slap him. apart from that the brakes look massive, and i like the wheels. good choice bman.

nfi Community Regular

nfi

Posted
Posted

Very nice! 8 piston just adds to the bling as well.

Have you investigated what pads the calipers support? I am guessing porsche?

Bman, to say you have had your fair share of dodgy dealings is a gross understatement :blush: Luckily for SAU club members you have taken enough bad luck to cover the 'team'....... I mean club :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...