Jump to content
SAU Community

Recommended Posts

Hey guys,

just want to throw some ideas around about the sever issues my friends car is now suffering after having a pcf installed and tuned at a fairly respectible brisbane workshop.

upon picking the car up my mate was told that they could not tune it to 11 psi as promised (std 33 turbo) as the actuator was screwed.. Now it was boosting up fine before taking it to the workshop - 8-9 psi arround 3k rpm as expected via a turbotech.

he drives it home and says car is running shit and lacking in power. Dyno sheets show 189 rwkw and good air fuel ratio. Now there is no torque graph, which i thought was strange? hiding something maybe.

anyhow full boost is not not made till arround 4-4500k rpm.. and it has been tuned to only run about 7 psi tops..

also car has all supporting mods, brand new fuel pump, fmic, pod full 3 inch zost with hiflow cat and now the pfc.

so i take it for a drive. strange rattle noise round the exhaust\turbo area.. lacking power for sure, boost does not hit hard. now we get home and let it idle. i can hear a rattley noise from arround the turbo exhaust housing when giving her a little rev. exhaust note sounds shit now aswell and not tough.. not to mention at idle she is blowing loads of black smoke and smeels badly like fuel.. and does not have a nice smooth idle. very up and down and just sounds wrong..

so from the above anyone got any clues as to what might be the problem. I am thinking possible exhaust wheel damage on turbo, hence rattles around the exhuast housing of the turbo..

Now if this is the case, would u not think a professional workshop would have known this and offered some advice more then just "mate your actuator is stuffed so it is not boosting properally" in which casue u would think they would replace it at a fee instead of trying to sell u a 3 grand turbo.

any ideas fellas

Link to comment
https://www.sau.com.au/forums/topic/134855-power-fc-r33-problems-help/
Share on other sites

yeah its possible it blew on the dyno

mine died on the street under load but it could fail at any time

the parts to replace it are about $100 all up

but u have to pull the turbo off, my dump gasket died

but we replaced all of them cos it was off and easy to do

Only way is to get it on a dyno and have a gander at the AFR's and the smoothness of the graph itself.

There isnt anything "dodgy" about not showing the torque figures on a dyno sheet mate

If the exhaust wheel was damaged and "rattling" around, it wouldnt be there now. It would have flown off the shaft.

Have you even spoken to the workshop the tuned it?

If it is indeed a manifold gasket, its no-ones fault. They get old and perish. Nothing you can do about it

umm maps a a biatch to type up.. i kinda have the written down, might take a pic..

i noticed all the airflow settings are 100 percent..

inj maps.. from 1x1 to about 5x5 it os 100.. from six x six up a bit it is at the 119 mark and at 20 x 20 she tops out at 123.

hope that kinda makes sense. try and get a pic...

only reason i thought no torque graph was suss, is cause the car has definately lost torque. but according tot he dyno sheets it has gained 10 kw top end and lost 3 psi of boost after the tune???

yeah does make sense, maybe we blew the gasket taking it for a drive after we got it back..

would the blown gasket cause shite loads of black smoke on idle though??

boost climbs but just does not snap up of full boost, just climbs slowly..

and nismoid, no have not spoken to the workshop yet as just the car back at 5pm, they closed up etc, so we'll speak to them tomorrow..

in no way am i tryin to blame them, just trying to figure out the chain of events that led to the car now barely running.

still the work shop said the actuator was fubared?? how many r33 stock turbos have stuffed atuators? is this common?

Would just like to stress the intention of this post is not to bag out any particular workshop, and i have not mentioned any names etc, so no need to get upset.. You know who you are..

One would imagine though if they took their car to a good workshop for a apexi power fc install and tune they would either come out with a smile from the new tune (from what I have read eveyone else raves about the powerfc) or an eplanation on why their car now runs like a pile of crap...

car is getting checked out soon.

Would just like to stress the intention of this post is not to bag out any particular workshop, and i have not mentioned any names etc, so no need to get upset.. You know who you are..

One would imagine though if they took their car to a good workshop for a apexi power fc install and tune they would either come out with a smile from the new tune (from what I have read eveyone else raves about the powerfc) or an eplanation on why their car now runs like a pile of crap...

car is getting checked out soon.

Glad your not trying to bag any work shops as this problem was definatly not the work shops fault. I don't understand how you can drive away with dyno graphs and a car that runs fine and then when it starts playing up you blame the tune, it just doesn't work this way. if there is something mechanically wrong with the car, no amount of tuning is going to fix it.

For those of you who are reading the thread, someone had been playing with the hand controller and had selected the "nismo option" AFM instead of the normal r33 GTST one, which caused the car to run like a piece of crap. With a new set of plugs and the correct AFM selected the car now runs fine again but the turbo is definatly on the way out as it's a little noisy (as was explained to the customer when he picked up the car).

It's very frustrating when you go out of your way to look after the customer and pay for the tow truck back to the work shop and it's due to someone playing around with things they don't know about. At least the car is running well again now which is the main thing I guess!!!

good to see it resolved and another case in point why if you dont know what you are doing the only screens you should should be looking at on your PFC HC is the monitor or sensor check screens.

  • 6 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...