Jump to content
SAU Community

Recommended Posts

Okay guys. I have been searching and searching and have been unable to find what I am looking for.

Esentially what I want is a two step launch controller for my GTR33. I want the type that allows boost to be built at a standstill so that you come off the line with full boost.

I know that the Power FC pro has a type of launch controller, however I dont believe it does what I am looking for. That plus the fact the discontinued the FC Pro. I also know that Bee-R has a rev limiter, however I believe that ALSO does not allow you to build boost on the line.

So, if someone could recommend one to me it would be GREATLY appreciated. Thanks.

-Sayajin

Link to comment
https://www.sau.com.au/forums/topic/153794-two-step-launch-for-gtr33/
Share on other sites

anything with a zero speed ignition cut should allow you to build boost. I know it works on my emanage ultimate

Such as what unit? Reason I ask is I am currently on the Power FC so I cant get a new stand alone just for launch control.

-Sayajin

Humm... this is a bit different from what I had heard before..

So I can set the rev limit to 6500RPM, stand full on the gas and it stays at the set RPM, and builds full boost while still on the line?

-Sayajin

yep got it in one. you have 2 rev limits one is a stationary (launch) rev limit that usualy is engaged either when speed = 0 or when handbrake is engaged. once speed is above 0 or handbrake is dropped it reverts to the usual rev limit. so you can set limit one to 6500rpm if you wish for launch, then limit 2 to 8000rpm for driving. as for whether it will build full boost I'm not so sure of that. it will build some boost though.

Okay guys. I have been searching and searching and have been unable to find what I am looking for.

Esentially what I want is a two step launch controller for my GTR33. I want the type that allows boost to be built at a standstill so that you come off the line with full boost.

I know that the Power FC pro has a type of launch controller, however I dont believe it does what I am looking for. That plus the fact the discontinued the FC Pro. I also know that Bee-R has a rev limiter, however I believe that ALSO does not allow you to build boost on the line.

So, if someone could recommend one to me it would be GREATLY appreciated. Thanks.

-Sayajin

It's hard to go past the MSD 2 step...

Ever used the Gizmo Paul? Now that you mention it I remember reading about it QUITE a while ago. I only ever heard of one person using it however so I am unsure on how well it works.

Any first hand experience?

*edit*

After reading the Apexi page all I can say is WOW.... Sounds like exactly what I want. Hell it even has flat shifting! (no lift to shift).

Also I read that it integrates with the shift light. Does that mean in order to get the Gizmo to work I need the shift light as well? Or just means it CAN work with it?

-Sayajin

Edited by Sayajin

no sorry, never used it. when i get an evo i will get one for sure

i see no use it for in my skyline (rear wheel drive & stock ceramic exhaust wheel)

from memory youll need or want;

stand alone ecu or good remap

steel wheel exhaust wheel

no cat

exhaust temp gauge might be a good idea

good traction

yeah its a nice device hey

yeah the shift light is optional that i can see

on the evo forums theres a video of one dude that has a 2 step spark cut limiter. the video shows the car stationary with 1.3 bar ready to go and lotsa flames out the exhaust

Humm.. well I have been reading around and it appears that the shift light is REQUIRED in order for the launch interface to work.

The Tach recall intercepts the RPM line from the ECU. This allows you to control your 2 shift points, warning and shift now - and also the launch.

A 5V signal is sent from the tach recall light to the launch control interface when the desired rev point for launch is reached.

Still seems like a great thing. I just personally feel the shift light is a bit too ricey for myself. I may have to make an exception however. That or just remove the bulb in the light. lol.

Or if someone else has something better that is just as well!

Thanks for the info Paul.

-Sayajin

Edited by Sayajin

Something you may want to think about is how is it actually limiting the rpm....

Yes some of the ECUs may have an option to hard / soft cut - fuel / spark but the million dollar question is how crudely they apply that limit.

My Haltech has these features too but I am planning to rely on the 2 step functionality built into my MSD DIS4

The reason I recommended the MSD is because the MSD alternates the cylinders it drops and some cheaper rev limiters may only drop the same cylinder causing fuel build up in that cylinder. Just make sure the ECU you plan to use alternates the cylinders.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...