Jump to content
SAU Community

Recommended Posts

Ok so i recently installed a DRIFT brand urethane pod filter to my RB25DE, Completly stock engine. And the performance drastically reduced, There was SFA backpressure when driving, And it was just really doughy and had shithouse throttle response. When i put the stock airbox back on it went back to normal. I had it installed properly with the AFM plug correctly on and everything was correct. Does anyone know why this had happened? and will i be better off leaving the airbox and putting a k&n panel filter in or something, Or figuring out a way to run a custom CAI into the top of the stock airbox with the K&N panel filter.

Any suggestions that people have that can improove the flow and maybe power with CAI setups please dont hold back im open to anything, Even if you have had a decent pod setup.

p.s

The pod filter was bracketed to the chassis of the car so it wasnt defectable, With no heat sheild or box to cover it. It still ran like shit regardless of the engine bay temp though.

josh.

Maybe if you run the pod down through the holes that the Turbo model intercooler pipes are meant to be so its got cold air from outside the car but i dont know if you can be stickered for it.

some filters use an oil to help filtration which affects the afm in some cases.

maybe you bumped the afm during installation?

just give the afm a quick clean and see how it goes.

possible... but that desnt explain why it ran fine again when he put the stock box back on though. I still think the air filter is of shit quality

lol... make sure its not one that says "Not recommended for turbo charged vehicles" on the bottom of the packaging

Maybe if you run the pod down through the holes that the Turbo model intercooler pipes are meant to be so its got cold air from outside the car but i dont know if you can be stickered for it.

I agree ^^^

Get an Apexi Dual Air Filter Cone it runs good for me

they are $150 odd arent they.

lol i cant afford that :D

That drift piece of shit was $54 for the pod and adapter :P

Edited by OBNXSH

i cant see any problem really with poor filter design, since it should be able to run without a filter at all with no problems.

my take on it is:

- oil used on filter.

- heat soak from engine causing high temps in the intake.

that said, it's been proven that a pod filter does SFA. the turbo guys are running 200+rwkw with the standard airbox with a decent panel filter.

if you really want to run a pod filter, then a custom air intake with a heat shield is a necessity.

I dont see how though, Ive seen this exact pod filter on many turbo cars and a few N/A cars and it ran fine with no problems...

Yea just get a K'N panel filter inside your stock airbox so it's nice and stealth, I wish I did that, I've got no idea where my stock airbox has gone now. So i'll be running my boxed PoD with the factory snorkel shooting air in for now.

Yea just get a K'N panel filter inside your stock airbox so it's nice and stealth, I wish I did that, I've got no idea where my stock airbox has gone now. So i'll be running my boxed PoD with the factory snorkel shooting air in for now.

I just got a k'n pod filter and it wouldn't fit into my stock box but i left the intake bit of the stockbox in place so it flows some air towards the filter and so far no problems, no noticeable decrease in power or nothing. I will be getting some heat shielding to "box" it in as such and using the stock air intake then i will have cold airflow going to it. Only problem i see is with my car R34 GTT there seems to be alot of hot air flow upwards towards the pod filter where as the other side of the car doesn't get that much hence why it needs to be "boxed in" and also so that it is legal.

  • 3 weeks later...

Does this help?

http://www.twinturbo.net/ttnetfaq/FAQpages/stall.html

It seems alot of the 300zx guys out there had problems with pod filters. Basically the link explains that by putting a thinnish strip of duct tape on one side of the pod it disrupts the air flow allowing the AFM to get a better reading. Try this first and see if it makes a difference.

Hope this helps!

Put the filter back on.

Chuck a slightly damp chamois over the filter (Not dripping wet, ring it out properly first!)

Now blip the throttle to some high revs.

Does the chamois get "sucked in"? no? Shit filter.

Yes? Problem isn't from it not flowing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Could be. Could also be that they sit around broken more. To be fair, you almost never see one driving around. I see more R chassis GTRs than the Renault ones.
    • Yeah. Nah. This is why I said My bold for my double emphasis. We're not talking about cars tuned to the edge of det here. We're talking about normal cars. Flame propagation speed and the amount of energy required to ignite the fuel are not significant factors when running at 1500-4000 rpm, and medium to light loads, like nearly every car on the road (except twin cab utes which are driven at 6k and 100% load all the time). There is no shortage of ignition energy available in any petrol engine. If there was, we'd all be in deep shit. The calorific value, on a volume basis, is significantly different, between 98 and 91, and that turns up immediately in consumption numbers. You can see the signal easily if you control for the other variables well enough, and/or collect enough stats. As to not seeing any benefit - we had a couple of EF and EL Falcons in the company fleet back in the late 90s and early 2000s. The EEC IV ECU in those things was particularly good at adding in timing as soon as knock headroom improved, which typically came from putting in some 95 or 98. The responsiveness and power improved noticeably, and the fuel consumption dropped considerably, just from going to 95. Less delta from there to 98 - almost not noticeable, compared to the big differences seen between 91 and 95. Way back in the day, when supermarkets first started selling fuel from their own stations, I did thousands of km in FNQ in a small Toyota. I can't remember if it was a Starlet or an early Yaris. Anyway - the supermarket servos were bringing in cheap fuel from Indonesia, and the other servos were still using locally refined gear. The fuel consumption was typically at least 5%, often as much as 8% worse on the Indo shit, presumably because they had a lot more oxygenated component in the brew, and were probably barely meeting the octane spec. Around the same time or maybe a bit later (like 25 years ago), I could tell the difference between Shell 98 and BP 98, and typically preferred to only use Shell then because the Skyline ran so much better on it. Years later I found the realtionship between them had swapped, as a consequence of yet more refinery closures. So I've only used BP 98 since. Although, I must say that I could not fault the odd tank of United 98 that I've run. It's probably the same stuff. It is also very important to remember that these findings are often dependent on region. With most of the refineries in Oz now dead, there's less variability in local stuff, and he majority of our fuels are not even refined here any more anyway. It probably depends more on which SE Asian refinery is currently cheapest to operate.
    • You don't have an R34 service manual for the body do you? Have found plenty for the engine and drivetrain but nothing else
    • If they can dyno them, get them dyno'd, make sure they're not leaking, and if they look okay on the dyno and are performing relatively well, put them in the car.   If they're leaking oil etc, and you feel so inclined, open them up yourself and see what you can do to fix it. The main thing you're trying to do is replace the parts that perish, like seals. You're not attempting to change the valving. You might even be able to find somewhere that has the Tein parts/rebuild kit if you dig hard.
    • Can you also make sure the invoices on the box (And none exist in the boxes) are below our import duty limits... I jest, there's nothing I need to actually purchase and order in. (Unless you can find me a rear diff carrier, brand new, for stupidly cheap, that is for a Toyota Landcruiser, HZJ105R GXL, 2000 year model...)  
×
×
  • Create New...