Jump to content
SAU Community

Recommended Posts

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

Chaser as well :D twin turbo 2.5L

hmmm wait a sec.. same engine as soarer.. are soarer's faster then r33's in stock form?

Same engine maybe, but the soarer is heavier... On power to weight it would go:

Chaser at 206kw in 1480kg-ish = 139kw/tonne

Skyline R33 at 185kw in 1360kg-ish = 136kw/tonne

Soarer at 206kw in 1560kg-ish = 132kw/tonne

Not that I'm suggesting that power to weight is the only factor that influences acceleration...

Hmmm.....Chaser for sure......

Does anyone Thought about the Tourqe from the TT motor should be significantly hight at Low reves than the R33...

Never really driven a chaser though... :D

Hmmm.....Chaser for sure......

Does anyone Thought about the Tourqe from the TT motor should be significantly hight at Low reves than the R33...

Never really driven a chaser though... :D

Dunno about that - I've always thought the 1JZ twin turbo to be slightly laggy... Although that experience is from a 16 year old Supra. The late model single turbo VVTi 1JZGTE is meant to be far better down low.

chaser. if the skyline was manual it b close i think especially if you got a good launch (good tyres)...

Damn....i though a Manual R33 could keep up with it, given that the chaser is Auto, I know there good..but never though that good.

I have Owned Both a 1997 Series II R33 GTST and a 1997 Toyota JZX100 Chaser Auto.

The Auto Chasers Maul Manual and Auto skylines with up to 200 rwkw.

I had a Catback exhaust on the Chaser and a K&N Pod filter and with the auto ran a 13.2.

On the street, most of my mates 200 rwkw Skylines got dusted. They develop a shitload more torque than the RB25, even More than a Standard RB26.

Beautiful car - get a Manual one though, so so much better and they can pull 13s with no mods whatsoever.

Just to remind you - a JZX90 - Pre 96 Model with the Old 1JZ would be on Par with an Auto R33 - after basic mods though would eat a 33.

JZX100s Came with a Different Motor alltogether - Single Turbo 1JZ VVTi.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
×
×
  • Create New...