Jump to content
SAU Community

Recommended Posts

  • Replies 256
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Got it Michael.

Currently 5 on the reserve list. But those NSW twats will probably pull out cause they are all soft.

I bet those NSW folk all come down with those bloody frangipani stickers all over their cars. They seem like such a NSW thing to have (and god damn I hate them!)
Steve-o is a poor example of what NSW has to offer :)
:(

I agree!!!

*throws egg at RCHOO acts like it wasnt her* :)

Ahhhhh God Bless Youtube

I was browsing some deca vids to show some of the WRX guys and I came across this,

and I didn't even know that was released :)

VIC FTW :)

Good to see the shit stirring has started ;)

Oh and that video.....again Sarah - Thanks for that ;)

Can some1 put me down on the reserve list? I willc ome anyway and help out.

Can some1 confirm with me that its cool?

Yep send me an entry form ASAP, and your in.

Entry list updated on Page 1. As always we have had people pull out. All reserves are in.

We will run with 55 entrants.

Yep send me an entry form ASAP, and your in.

Entry list updated on Page 1. As always we have had people pull out. All reserves are in.

We will run with 55 entrants.

ok faxed and confirmation it was ok. Payment sent today also via DD. cheers Chris.

Chris. :whistling:

entrant 55 ftw.

Entry list updated on Page 1. As always we have had people pull out. All reserves are in.

We will run with 55 entrants.

Sweet... CAMS licence is sorted, my cousin is driving my car up for me. I'm all set!

Erm...I've been daft and forgotten all about organising a CAMS licence for this Saturday...

Are we still able to download a form from the web and bring it along and pay on the day?

I'm pretty sure it's this form: http://www.cams.com.au/downloads/paperform...Application.pdf

Correct?

:rant:

Erm...I've been daft and forgotten all about organising a CAMS licence for this Saturday...

Are we still able to download a form from the web and bring it along and pay on the day?

I'm pretty sure it's this form: http://www.cams.com.au/downloads/paperform...Application.pdf

Correct?

:rant:

That should be fine mate

I remember i did mine the same way..

Just remember to have correct money on the sat morning/and filled out correct..

That should be fine mate

I remember i did mine the same way..

Just remember to have correct money on the sat morning/and filled out correct..

Yep that's fine. Fill it out, bring it along and hand over the cash at registration in the morning.

Event Schedule is now released.

Event Schedule :

FTP Mirror

HTTP Mirror

Updated on 1st post also.

I'm big kev excited...

We have also had a record number of people pull out of this DECA. (9)

So I can accept 3 more entries if anyone else is keen on coming along.

If you are I would appreciate knowing before 6pm tonight. So fax in the entry form ASAP and send an email to [email protected], as I wont be checking the fax machine unless I have to. (i'm not at work)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...