Jump to content
SAU Community

Recommended Posts

bought a 180 with the front smashed in witch we will be converting to a sil80 and dropping an RB into.

some people believe that they can be a bit front heavy for drift but gonna give it a crack anyways.

it will have FMIC, pod and probably bigger fuel pump. and will be running higher boost on stock turbo (about 12 - 14 pound)

will be getting coil overs and strut braces as well.

how do you recon it will handle and what sort of power do u recon i would get???

Link to comment
https://www.sau.com.au/forums/topic/166764-rb20-turbo-sil80-drift-car/
Share on other sites

My drift car is a Onevia with a Rb20 in it and a RB25 box.

Completely stripped interior just a RB25 highflow, remap, 3" exhaust, front mount, Tein coil overs, welded diff and a 5 puk button clutch. :)

No problems drifting whatsoever.

Do it and have fun :P

The Cefiro cross member is the best to use as it will sit the engine a couple of cm lower then when using a R32 GTST cross member.

Just get your suspension sorted out and it will be easy to throw around.

A 1 piece tail shaft is fine and most big truck shops like Gibbs can make you one up relatively cheaply.

If you have any questions feel free to send us a PM.

I think what people are trying to tell you is how much effort and cash is needed to make it a reality . A long heavy motor thats no torque mountain in std form - for drift . No competitive engine is going to be cheap regardless of if its in the car or on the floor . I think you'll find in this day and age more factory and aftermarket goodies for SR20's than RB20's which means greater availibility and lower cost for the right bits . I can partly understand why in the US there is this S13/RB20 craze - no R32/33/34's or SR20DET USDM cars . If they'd had the R32GTST they wouldn't bother converting S13's . When you can have 400 ft/lbs of torque from a half serious SR20 at 4500 rpm why would you plonk an RB20 into it ?

One more time , said this last time .

Search FreshAlloy.com Forums - Twin scroll question .

Cheers .

Putting a RB20 makes zero sense.

...except they are cheaper, stronger and possibly make the same/more power. Im yet to be convinced that a std SR20 can make the power and response a sorted RB20 can. I think its more to do with the fact that there are so many ppl spending money on SR20s its easy to find a good one. The same cant be said for RB20.

They arent the best engine. But if dollars are tight then i think the RB20 should be on the radar.

...except they are cheaper, stronger and possibly make the same/more power.

id say that is more a tuner fault, SR's are far more det prone than rb20s for sure and 90% of sr's failures are ring land and the rest are big end...... due to det. i have only ever lost one SR and it was a dodgy HKS injector that stopped working.... killed number 3.

sure they are cheaper but by the time its installed 2500 goes quite a way to making pwr on the sr. if it is NA to start with then yes probaly makes sense.

i see SR packages from 1500 regulary you just need to look.

The Cefiro cross member is the best to use as it will sit the engine a couple of cm lower then when using a R32 GTST cross member.

as slide said im using r32 gtst cross member and i needed to lift the bonnet a bit to fit the engine under it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...