Jump to content
SAU Community

Recommended Posts

not sure on the logic of more boost using less fuel haha.. but .. its worth a try.

I think I am going slightly mad.. but I remember saying somewhere that the stagea

o2 sensors are supposed to be replaced at 40 and 80 thousand kays..

so I bet a lot of people that have imported a stag at say 100,000 have never

had the o2 sensor replaced ever.

its on our list of things to do next weekend

calculated it currenty and its around 15L / 100km

hmmmm.... not sure if my o2 sensor was replaced when the conversion was done or not... may have to give that a try: it can't hurt (except my wallet). What's a replacement 02 sensor worth, anyone?? Will it be different for a '26??

I have run mostly 98 RON but running 95 RON doesn't seem to make any difference to the economy or running of the car.

Pity BP don't give any discounts on fuel. Which means that I have to keep going back to Woolworths liquor to get my discount vouchers so that I can get my 4c off the fuel..... well that's my excuse! :P

Caltex/Woolies Vortex 98 seems alright anyway. But every now and then I am probably gonna run a tank of 95.

yeah I've done the 02 sensor, they are dirt cheap just pick up the ngk one for the 33 gtst, it did help but not as much as I was hoping :P

Is there a discription of how to do his? Are the 33 O2 sensors the same for the series 2 as well?

hmmmm.... not sure if my o2 sensor was replaced when the conversion was done or not... may have to give that a try: it can't hurt (except my wallet). What's a replacement 02 sensor worth, anyone?? Will it be different for a '26??

I think you might need two for the '26, but for the RB25 they're around $80each, last I remember...

Is there a discription of how to do his? Are the 33 O2 sensors the same for the series 2 as well?
go buy an o2 sensor socket

and remove

it takes all of 10 minutes total to do it

There should be a description in the DIY threads, if not in the Stagea section then definitely in one of the other maintenance sections.

As Grant said, it's not a difficult job to do if you have the right tools, but due to exposure to heat, the sensor can be physically hard to remove. A bit of WD40 and some elbow grease is pretty much all that you need.

lol it is that easy too.

rb25 (series 1) direct fit is OZA395-E2

rb25 (series 2) just a generic one like EL ford, need to change plug

rb26 is OTD2F-P1P (rear direct fit ) and same again or generic for front need to change plug

I have run mostly 98 RON but running 95 RON doesn't seem to make any difference to the economy or running of the car.

Pity BP don't give any discounts on fuel. Which means that I have to keep going back to Woolworths liquor to get my discount vouchers so that I can get my 4c off the fuel..... well that's my excuse! :D

Caltex/Woolies Vortex 98 seems alright anyway. But every now and then I am probably gonna run a tank of 95.

lucky for us we have a BP near us that does do 4cents off so thats my winner :rofl::domokun: I find with Woolies Vortex98 i dont get as many km's to a tank????

Good call, thanks Grant - would have thought of that a little late! :D

ive done it before not thinking

went and started swapping a turbo on a friends car he just got done driving.....really hurt

lucky for us we have a BP near us that does do 4cents off so thats my winner :D:rofl: I find with Woolies Vortex98 i dont get as many km's to a tank????

Hey Kirstie, which BP gives the discount and how do ya get it?

Cheers, Al

what size (external nut diameter ) are most of the o2 sensors?

I wonder if a standard deep socket would work?

yeah seeing where the sensor is .. its definately going to be much easier to remove with a dedicated socket. Right tool for the job and all that !

I still as yet have to get a consult cable on the car and check for fault codes - I have been so slack!

what size (external nut diameter ) are most of the o2 sensors?

I wonder if a standard deep socket would work?

yeah seeing where the sensor is .. its definately going to be much easier to remove with a dedicated socket. Right tool for the job and all that !

Is it just a matter of undoing the old sensor? Like a spark plug?

yeha

but unless you cut off the lead fmor your OLD o2 sensor you cant use a socket

the O2 socket has a gap you can slide the wire out of

i have one, best investment ever when i need to remove it

other option is to take off your o2huosing and then remove with a wrench.

But go to your local parts store

its like 20 bucks for hte socket

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSP male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSP reducing bush?
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...